Datamax MICROFLASH 4T Руководство
Просмотреть онлайн или скачать pdf Руководство для Принтер Datamax MICROFLASH 4T. Datamax MICROFLASH 4T 2 страницы. External charger swivel lock
Также для Datamax MICROFLASH 4T: Краткое руководство по эксплуатации (2 страниц)
MF4 External Charger Swivel Lock
(220226-003)
Swivel
AC
AC
Foot
Lock
Adapter
Adapter
Cradle
Figure 1
Parts List
(1) MF4 External Swivel Lock Depot Charger
(1) High capacity AC adapter
(1) Grounded AC power cord
(7) #10 x 1¼" wood screws (not shown)
(7) #10 flat washers (not shown)
#8 - #10 toggle bolts [not included; length to be
determined by the user
Note: Use #10 x 1¼" wood screws to mount the
charging dock to wood surfaces only. The
#10 x 1¼" wood screws cannot be used to mount
the depot charger to any other type of surface.
Use #8 - #10 toggle bolts if you are mounting the
depot charger to drywall.
Guidelines
General Guidelines
•
The MF4 Depot Charger is designed to be used as a
desktop or wall mounted unit.
•
Keep the charging dock in a cool, dry place, away from
direct sunlight, high temperature, and moisture.
•
The depot charger takes approximately 3-4 hours to
charge each printer. If multiple printers are attached, the
charge time remains at approximately 3-4 hours per
printer; however, charge times may vary.
•
The depot charger is not recommended for use with the
MF2t Smart CardReader (SCR) or MF4t Smart
CardReader (SCR) printers.
DC
Grounded
•
Power
When connected to the depot charger, the printer(s) may
AC Power
Jack
Supply
not print.
Cord
Safety Guidelines
•
Do not short the contacts.
•
Use only an Datamax-O'Neil approved power supply.
•
Position the depot charger with enough room to properly
open and close the printer(s); position the depot charger
so it is protected from environmental elements such as
moisture, tools, and boxes; and position the depot
charger in a secure area in normal traffic patterns.
•
Do not operate the depot charger if it appears damaged.
•
To reduce risk of electric shock, unplug the depot charger
before cleaning.
•
Batteries become warm to the touch during charging. If
the battery becomes too hot to touch, discontinue
charging and contact Datamax-O'Neil.
•
Use of any charger or battery not approved by
Datamax-O'Neil for use with their printers
could cause damage to the batteries or printer and will
void the warranty.
•
Datamax-O'Neil does not accept liability for
improperly mounted or poorly placed printers and/or
depot charger.
Mounting the Depot Charger
If the depot charger will be mounted on a vertical
surface or on a wall, use the following procedure to
mount the charging dock:
1. Remove rubber bumpers from the
feet's and AC Adapter cradle.
2. Locate the mounting holes. There are two
mounting holes on either end of the
(Figure 3) and two mounting holes in the middle
of the
(Figure 4).
depot charger
Figure 4
Figure 3
3. Use the
as a template to mark the
depot charger
mounting holes on the mounting surface
(Figure 5). For information on mounting, see the
Guidelines in the previous section.
Figure 5
4. Drill the mounting holes at the marked locations.
Warning: Use caution when drilling the
mounting holes and when mounting the
charger
onto a wall.
5. Attach the
to the mounting surface
depot charger
as follows:
Drywall Surface: Use #8 - #10 toggle bolts (not
included).
Wood Surface: Use #10 x ¼" wood screws.
#10 x ¼" wood screws cannot be used on any
other type of surface.
6. Verify the
is level.
depot charger
7. Thread the screws through the washers,
charger
, and mounting holes and tighten securely.
8. Proceed to Attaching the Power Supply.
depot charger
depot charger
depot
depot