DVM International DVM-SA30IR Руководство

Просмотреть онлайн или скачать pdf Руководство для Дымовая сигнализация DVM International DVM-SA30IR. DVM International DVM-SA30IR 2 страницы.

Печатать страницу

Model: DVM-SA30IR

PRODUCT SPECIFICATIONS

Warranty period: Lifetime = 10 years.

After that, the smoke detector must be replaced.

Look for the production date on the sticker of the detector.

Power supply: Fixed Lithium battery 3 VDC (CR17450), battery not

interchangeable

Alarm Volume: >85dB (A) at 3 meters distance

Alarm Sensitivity: 0.10-0.16dB /m

Alarm Pause: About 8 minutes

Complies With: EN14604:2005/AC: 2008

Sound Pattern: ISO8201 (Beep 0.5s – Pauze 0.5s – Beep 0.5s – Pauze 0.5s – Beep 0.5s

– Pauze 1.5s while the red LED flashes. This pattern is repeated over and over

again.

Sound pattern of the wireless interconnection: Beep-Beep – Pause 1.2s. This pattern

is repeated over and over again.

DESCRIPTION

This is an optical smoke detector. These are particularly sensitive to detecting

visible microparticles (which arise from smoldering fires) and react faster than

ionization smoke detectors. An example of such smoldering fires is a burning

cigarette on a couch or bed, a common cause of devastating fires. Please note

that this device does not detect flames, temperature/heat, carbon monoxide or

other dangerous gases. The smoke detector has many advanced features and

a long service life with the fixed battery.

RECOMMENDED LOCATIONS FOR SMOKE

DETECTORS

1. Your smoke detector is suitable for the landing, hall, bedroom, living room and

dining room.

2. Install it in the stairwell and on each floor.

3. Smoke, heat and burning things spread horizontally after rising to the ceiling,

so install the alarm in the middle of the ceiling of a standard built house.

4. If for some reason the alarm cannot be installed in the middle of the ceiling,

the distance from the smoke detector to the wall should be at least 30 cm (see

Figure 1).

5. If the length of the room or hall is more than 10 meters, you need to install

several alarms there.

6. If the ceiling slopes, the smoke detector should be installed at least 50 cm from

the highest ceiling point in the room (see Figure 2).

Attention: This smoke detector is also suitable for installation in caravans, motor

homes and mobile homes.

30 cm

Ceiling

Figure 1

LOCATIONS TO AVOID

1. Avoid the environment of appliances or places where normal combustion

regularly takes place (such as in kitchens, near stoves, hot water boilers, etc.).

Use specialized smoke detectors, such as temperature detectors, for these areas

to prevent unwanted alarms.

2. Keep at least 3 meters away from rooms with high humidity, such as

bathrooms or rooms near dishwashers or washing machines.

3. Keep a minimum distance of 1 meter from air vents or ventilation openings for

heating and cooling. The air can blow away/suck away smoke from the

detector, preventing the detector from sounding the alarm (in time).

4. Avoid areas where the temperature may fall below 5°C or above 40°C.

5. Avoid extremely dusty or dirty environments. The dust particles prevent the

detector from functioning properly.

6. Also avoid the airflow of (loose) air conditioning units and fans.

ACTIVATE:

Press and hold the test button for about 3 seconds until the LED lights up. Then

release the test button within about 2 seconds. The smoke detector gives a beep

signal to indicate that it is activated and enters the working state.

WIRELESS INTERCONNECTION FUNCTION

1. Make sure all smoke detectors are activated.

Thank you for purchasing our smoke

detector. Take a few minutes to read the

user manual thoroughly and

familiarize yourself and your family

with how the smoke detector works.

And save it for future reference.

1116

DoP: RD-380D-HR-24-001

EN 14604:2005/AC:2008

Figure 2

2. Select one of the smoke detectors as the MASTER detector. Treat all other

smoke detectors as SLAVE detectors.

3. Press the master's test button three times within two seconds. The red LED

flashes quickly. The MASTER smoke detector is now in transmit mode for the

radio signal. This mode lasts 48 seconds.

4. While the MASTER smoke detector is in radio signal mode, press the test button

of a SLAVE detector three times within two seconds. The SLAVE detector stores the

signal from the MASTER detector and completes the pairing and gives a beep

with flash as confirmation.

5. Repeat the above steps on all other SLAVE detectors.

Clear wireless connection function

1. Determine which SLAVE detector should have the connection function

cleared.

2. Press the test button of the SLAVE detector three times within two seconds. The

red LED flashes quickly.

3. Press and hold the test button again until the red LED goes out the first time,

then release the test button immediately. The red LED will flash slowly.

4. Now press the test button again. The SLAVE detector beeps three times, which

means that the SLAVE detector has erased the wireless connection.

ATTENTION:

The smoke detector must first be activated, otherwise it will not work.

Thesmoke detector is designed to be wireless paired with up to 40 other smoke

detectors.

The smoke detectors are not designed to be paired with wireless detectors from

other series or manufacturers. The smoke detectors must first be connected to

each other in order to work in a coupled manner.

If one detector goes into alarm, all other, interconnected detectors, also go into

alarm. Only smoke detectors that are successfully linked can transmit the alarm.

If you clear the pairing, only the slave detector pairing is removed. The MASTER

detector cannot clear the link.

INSTALLATION:

WARNING: To prevent injury, the smoke detector must be securely

attached to the ceiling, as described below.

Installation drawing

DECKE

Tighten

OPERATION AND TESTING:

Testing

Press the test button. If the detector works correctly, the alarm will go off. If the

alarm does not go off, the battery is empty or the smoke detector is defective.

DO NOT USE an open flame to test your detector! You can use this to damage the

detector or cause a fire.

NOTE: Test the smoke detector every week!

Resting state:

The red LED flashes 1 time every 48 seconds to indicate that the smoke detector

is active.

Alarm state:

When the detector detects combustion products, it gives a sound alarm and the

red LED flashes once every second. The sound alarm and the flashing LED

continue until the air is clean again.

Boreholes

Mounting plugs

Screws

Unscrew

Smoke detector

Figure 3