Austral Lock Gainsborough YARRA HORIZON FLAT OUTER PULL Инструкции по установке
Просмотреть онлайн или скачать pdf Инструкции по установке для По замкам Austral Lock Gainsborough YARRA HORIZON FLAT OUTER PULL. Austral Lock Gainsborough YARRA HORIZON FLAT OUTER PULL 2 страницы.
Печатать страницуYARRA HORIZON FLAT OUTER PULL
These instructions describe the steps to install a standard Yarra Horizon
lock for general application. For other Yarra Horizon variations and non-
standard applications, additional instructions may be required.
Read through all instruction steps before beginning installation. When
replacing an older lock, modify the existing installation holes in the door
stile and jamb if necessary.
Please note: Packers are sold separately.
1.
Door preparation
•
For optimal installation, ensure the door is rolling smoothly and
closing parallel into the jamb by lubricating and adjusting the rollers.
Close the door and lightly mark the door stile at the edge of the
overlapping jamb.
•
Prepare 3 9.0mm holes in the door stile as dimensioned below in
Figure A. Enusre the holes are straight and free from burrs.
Figure A
Door Stile
Door Jamb
Mark and
measure
from this
edge
Mark
19.0 mm
Door Stile
28.0 mm
2.
(optional)
•
If a cylinder is not being used in the Outer Pull, proceed to STEP4.
•
To remove a Cylinder Plug and install a Keyed Cylinder into the
Outer Pull, remove the Fixing Screw and remove the Cylinder Plug.
(refer Figure B). The Cylinder Plug can be discarded.
•
Use the table in Figure C below to determine the required Spindle
length. NOTE: If using packer(s), add the total packing thickness
to the door thickness, then use this value in the table below.
•
Use pliers or a vice to carefully break off the required number of pre-
notched portions of the Spindle to suit the door thickness.
•
Install the keyed cylinder spindle and spindle holder onto the outer
pull and install long fixing screw as shown in Figure B.
Figure B: Exterior
Pull Assembly
Cylinder plug screw
Long fixing screw
Exterior
Interior
14.0 mm
Ø 9.0 mm
Spindle Holder
41.0 mm
41.0 mm
Cylinder installation
Cylinder Plug
OR
Keyed Cylinder
Spindle
3.
Cylinder installation CONT.
(optional)
•
Use the table below with Figure C to decide the correct length of
the Spindle. Add the packer thickness to the door thickness in table
if using packers. If necessary, use pliers or a vice to carefully break
off the required number of pre-notched portions of the Spindle to
suit the door thickness.
Door thickness
Spindle preparation
41.8 to 35.6 mm
Break off '1' portion
35.5 to 29.3 mm
Break off '2' portions
29.2 to 23.0 mm
Break off '3' portions
22.9 to 20.8 mm
Break off '4' portions
Figure C
Spindle
Discard
Notch
4.
Select fixing screws
•
Several pairs of Fixing Screws are provided to suit different door
thicknesses. Use the table below to identify which are the correct
length Fixing Screws. Add the packer thickness to the door
thickness in table if using packers.
Door thickness
41.8 to 35.6 mm
35.5 to 29.3 mm
29.2 to 23.0 mm
22.9 to 20.8 mm
PLEASE TURN PAGE FOR INSTALLATION STEPS 5 - 8
Screw selection
1 3/4" Fixing Screw
1 1/2" Fixing Screw
1 1/4" Fixing Screw
1" Fixing Screw