Australian Direct ADCHG128 Руководство пользователя - Страница 4

Просмотреть онлайн или скачать pdf Руководство пользователя для Зарядное устройство Australian Direct ADCHG128. Australian Direct ADCHG128 12 страниц. Smart battery charger 12v 8a, suitable for 12v normal lead acid, sealed, agm or gel batteries between 10-150ah, ip65

Печатать страницу

1. Operation

FEATURES

Automatic and Intelligent 9-Stage Charging Curve

The AD Battery Charger is controlled by a microprocessor with 9-stage charging characteristic for charging

batteries automobiles, motorcycles, snow mobiles, tractors, personal watercraft, boats etc.

The microprocessor senses the condition of the battery and controls the regulator to provide the right current

and voltage to the battery (charging characteristic). This will give the best eﬀect on charging and give the

longest life to battery.

Charging characteristic:

BATTERY

DESULPHATION

TEST

5V~14.0V

2A until the voltage

12V/SLOW

good condition

drops less than 2V

2A until the voltage

12V/GEL

5V~14.0V

good condition

drops less than 2V

FAST

2A until the voltage

12V/AGM

5V~14.0V

good condition

drops less than 2V

FAST

2A until the voltage

5V~14.0V

12V/Recond

good condition

drops less than 2V

Limit

Detection

Max 4h

LED 1 - BATTERY TEST: Checks the battery voltage to make sure battery connections are good and the

battery is in a stable condition before beginning the charge process.

LED 2 - DESULPHATION: Detects sulfated batteries. Pulsing current and voltage, removes sulfate from the

lead plates of the battery restoring the battery capacity.

LED 3 - SOFT START: Initial battery test to determine battery condition. If the battery is severely discharged,

charger will begin the Soft Start stage. Charging starts with reduced current until battery voltage reaches a

normal condition for charge.

LED 4 - BULK: Major charging stage where the battery receives the majority of its charge. During this stage the

battery brought to 75 - 80% of its charger. The charger delivers maximum current until the terminal voltage

has risen to the full charge level for Normal battery.

LED 5 - ABSORPTION: Completes the charge up to virtually 100% at a constant voltage. The current tapers oﬀ

after the current reached the minimum level.

LED 6 - RECONDITION: Select "Recondition" mode, charged by higher voltage to recondition the sulfate of the

battery to save battery life.

LED 7 - ANALYSIS: Tests if the battery can hold charge. Batteries that can not hold charge may need to be

replaced.

LED 8 - FLOAT: Low constant voltage, minimal charge current, battery is fully charged.

LED 9 PULSE: Maintaining the battery at 95-100% capacity. The charger monitors the battery voltage and

gives a pulse when necessary to keep the battery fully charged.

SOFT

BULK

ABSORPTION

START

increasing voltage

Declining current

1A until 10V

to 14.4V 2A

14.4V

increasing voltage

Declining current

1A until 10V

to 14.4V 8A

14.4V

increasing voltage

Declining current

1A until 10V

to 14.4V 8A

14.7V

increasing voltage

Declining current

1A until 10V

to 14.7V 8A

14.7V

Max 9h

Max 36h

ANALYSIS

RECONDITION

Checks if voltage

N/A

13.20-14.1 4h

drops less than 2V

Checks if voltage

N/A

13.20-14.1 4h

drops less than 2V

Checks if voltage

N/A

13.30-14.1 4h

drops less than 2V

Max

Checks if voltage

13.30-14.1 4h

15.7V, 2A

drops less than 2V

4h charge cycle

Max 2h

1.5 seconds

voltage drops

FLOAT

PULSE

13.0 - 14.4

13.0 - 14.7

Charge cycle

restarts if

voltage drops