BENDIX QRV QR-1 QUICK RELEASE VALVES Ссылка - Страница 2
Просмотреть онлайн или скачать pdf Ссылка для Блок управления BENDIX QRV QR-1 QUICK RELEASE VALVES. BENDIX QRV QR-1 QUICK RELEASE VALVES 4 страницы. Quick release valves
Печатать страницу
PREVENTIVE MAINTENANCE
Important: Review the Bendix Warranty Policy before
performing any intrusive maintenance procedures. A warranty
may be voided if intrusive maintenance is performed during
the warranty period.
No two vehicles operate under identical conditions, as a
result, maintenance intervals may vary. Experience is a
valuable guide in determining the best maintenance interval
for air brake system components. At a minimum, the QR-1
valve should be inspected every 12 months or 3600 operating
hours, whichever comes first, for proper operation. Should
™
the QR-1
valve not meet the elements of the operational
tests noted in this document, further investigation and service
of the valve may be required.
OPERATING AND LEAKAGE TESTS
While holding a foot brake valve application:
1. Coat the exhaust port with a soap solution; leakage of a
1" bubble in 3 seconds is permitted.
2. Coat the body and cover with a soap solution. No leakage
is permitted between body and cover.
If the valve does not function as described, or if leakage is
excessive, it is recommended that it be replaced with a new
or remanufactured unit, or repaired with genuine Bendix parts.
GENERAL SAFETY GUIDELINES
WARNING! PLEASE READ AND FOLLOW
THESE
INSTRUCTIONS
PERSONAL INJURY OR DEATH:
When working on or around a vehicle, the following
general precautions should be observed at all times.
1. Park the vehicle on a level surface, apply the
parking brakes, and always block the wheels.
Always wear safety glasses.
2. Stop the engine and remove ignition key when
working under or around the vehicle. When
working in the engine compartment, the engine
should be shut off and the ignition key should be
removed. Where circumstances require that the
engine be in operation, EXTREME CAUTION should
be used to prevent personal injury resulting from
contact with moving, rotating, leaking, heated or
electrically charged components.
3. Do not attempt to install, remove, disassemble or
assemble a component until you have read and
thoroughly understand the recommended
procedures. Use only the proper tools and observe
all precautions pertaining to use of those tools.
2
4. If the work is being performed on the vehicle's air
5. Following
™
6. Never exceed manufacturer's recommended
7. Never connect or disconnect a hose or line
8. Use only genuine Bendix
9. Components with stripped threads or damaged
TO
AVOID
10. Prior to returning the vehicle to service, make
11. For vehicles with Antilock Traction Control (ATC),
REMOVING AND INSTALLING
REMOVING
Block vehicle wheels and/or hold vehicle by means other
than air brakes.
Drain all air brake system reservoirs.
Disconnect air lines from valve.
Remove mounting bolts, then valve.
brake system, or any auxiliary pressurized air
systems, make certain to drain the air pressure from
all reservoirs before beginning ANY work on the
vehicle. If the vehicle is equipped with an AD-IS
air dryer system or a dryer reservoir module, be
sure to drain the purge reservoir.
the
vehicle
recommended procedures, deactivate the electrical
system in a manner that safely removes all
electrical power from the vehicle.
pressures.
containing pressure; it may whip. Never remove a
component or plug unless you are certain all
system pressure has been depleted.
components and kits. Replacement hardware,
tubing, hose, fittings, etc. must be of equivalent
size, type and strength as original equipment and
be designed specifically for such applications and
systems.
parts should be replaced rather than repaired. Do
not attempt repairs requiring machining or welding
unless specifically stated and approved by the
vehicle and component manufacturer.
certain all components and systems are restored
to their proper operating condition.
the ATC function must be disabled (ATC indicator
lamp should be ON) prior to performing any vehicle
maintenance where one or more wheels on a drive
axle are lifted off the ground and moving.
®
manufacturer's
®
replacement parts,