BENDIX ST-1 ST-3 SAFETY VALVE Руководство - Страница 2
Просмотреть онлайн или скачать pdf Руководство для Блок управления BENDIX ST-1 ST-3 SAFETY VALVE. BENDIX ST-1 ST-3 SAFETY VALVE 4 страницы. Safety valve
Печатать страницу™
DISASSEMBLY: ST-1
1. Clamp lower wrench flat in vise (flat nearest pipe thread).
2. Using upper wrench flat, unscrew lock nut. Unscrew and
remove spring cage from body of valve.
3. Remove ball valve, spring and release pin from spring
cage.
™
DISASSEMBLY: ST-3
1. Clamp spring cage in soft jawed vise.
2. Using wrench flat, unscrew body from spring cage.
3. Remove ball valve, spring and release pin from spring
cage.
CLEANING AND INSPECTION
Clean all parts in mineral spirits. Inspect all parts. All parts
not considered serviceable should be replaced with genuine
Bendix replacement parts.
™
ASSEMBLY: ST-1
ADJUSTABLE VALVE
1. Place the ball valve in body.
2. Install spring and release pin in spring cage with adjusting
screw.
3. Position the release pin overball valve. Screw body with
ball into the spring cage. Tighten securely.
4. Adjust for proper setting (see "Adjustment" section).
™
ASSEMBLY: ST-3
NON-ADJUSTABLE VALVE
1. Install spring, release pin in spring cage.
2. Position ball valve in body and screw spring cage onto
body.
3. Hold spring cage in soft jawed vise and tighten body
securely.
TO RAISE PRESSURE SETTING
1. Loosen lock nut.
2. Turn adjusting nut clockwise to obtain correct pressure
setting.
3. Tighten lock nut.
TO LOWER PRESSURE SETTING
1. Loosen lock nut.
2. Turn adjusting nut counter clockwise to obtain correct
pressure setting.
3. Tighten lock nut.
TESTING OF REBUILT SAFETY VALVES:
Perform operating and leakage checks.
ADJUSTMENT OF SAFETY VALVE
™
NOTE: The ST-3
safety valve is not adjustable.
The pressure setting of the safety valve is stamped on the
cover wrench flat (closest to the pipe thread). The vehicle
manual may also provide the proper pressure setting. If
setting is not known, determine governor cutout pressure
setting and adjust safety valve so that the safety valve closes
at a pressure setting somewhat above governor cutout
pressure setting (See "Operation" section).
2
ADJUSTABLE VALVE
NON-ADJUSTABLE VALVE
ADJUSTING
NUT
SPRING
CAGE
BALL
VALVE
PIPE
THREAD
SPRING
CAGE
BODY
PIPE
THREAD
To adjust, the safety valve must be connected to an air
system with air pressure in excess of desired setting. It is
important that an accurate gauge be used to check pressure
settings while making adjustments.
WARNING! PLEASE READ AND FOLLOW
THESE
INSTRUCTIONS
PERSONAL INJURY OR DEATH:
When working on or around a vehicle, the following
general precautions should be observed at all times.
1. Park the vehicle on a level surface, apply the park-
ing brakes, and always block the wheels. Always
wear safety glasses.
2. Stop the engine and remove ignition key when
working under or around the vehicle. When work-
ing in the engine compartment, the engine should
be shut off and the ignition key should be removed.
Where circumstances require that the engine be
in operation, EXTREME CAUTION should be used
to prevent personal injury resulting from contact
with moving, rotating, leaking, heated or electri-
cally charged components.
3. Do not attempt to install, remove, disassemble or
assemble a component until you have read and
thoroughly understand the recommended proce-
dures. Use only the proper tools and observe all
precautions pertaining to use of those tools.
RELEASE
PIN
LOCK
NUT
™
ST-1
SAFETY
SPRING
VALVE
BODY
RELEASE
PIN
SPRING
BALL
VALVE
™
ST-3
SAFETY
VALVE
TO
AVOID