Dyna CSADL6000IE/E Инструкции по установке, эксплуатации и техническому обслуживанию - Страница 7

Просмотреть онлайн или скачать pdf Инструкции по установке, эксплуатации и техническому обслуживанию для Портативный генератор Dyna CSADL6000IE/E. Dyna CSADL6000IE/E 12 страниц.

Печатать страницу

Although individual units and models may vary slightly, the

normal voltage and frequency of the engine-generators

described in this book are approximately as follows, under

varying loads:

LOAD vs. OUTPUT

__________________________________________________________________________________________________________________

Generator

Frequency

Load

Speed

Applied*

(RPM)

__________________________________________________________________________________________________________________

None

3750

Half

3600

Full

3540

__________________________________________________________________________________________________________________

*Portion of plant's rated output current.

The speed of the engine was carefully adjusted at the factory

so that the generator produces the proper voltage and

frequency. For normal usage, the speed setting should not

be changed. If the generator is being run continuously on a

very light load, it is often advisable to lower the operating

speed slightly. Whenever making any speed adjustments

check the unit with a voltmeter or tachometer and be sure the

speed is correct.

Lower voltage may damage both the generator and any load

connected to it. Running the engine at excessively high

speeds results in high voltage, which may significantly

shorten the life of appliances being used.

Output voltage should be checked periodically to ensure

continued proper operation of the generating plant and

appliances. If the generator is not equipped with a voltmeter,

it can be checked with a portable meter. Frequency can be

checked by using an electric clock with a sweep second

hand. Timed against a wrist watch or a stop watch the clock

should be correct within +/- 2 seconds per minute.

OPERATING YOUR GENERATOR

The engine-generators covered in this manual were designed

for portable use. DO NOT INSTALL OR OPERATE THIS

GENERATOR INDOORS. The unit should be stored in a

warm dry location. During a power outage, move the unit

outdoors to a flat dry location such as a driveway or sidewalk.

Allow the engine to warm up for two or three minutes before

applying any load. This will allow the engine to reach normal

operating temperature and oil to circulate throughout the

engine. A short warm-up time will permit the engine to work

more efficiently when the load is applied and will reduce the

wear in the engine, extending its life.

Receptacles have been provided to allow loads to be

connected to the generator. The loads should be added one

at a time. If a large motor is being started or multiple motors

are being started, they should be started individually and the

largest should be started first

Most electric tools and appliances will have the voltage and

amperage requirements on their individual nameplates.

When in doubt consult the manufacturer or a local electrician.

The nameplate amperage rating for electric motors can be

misleading. See "Starting Electric Motors" in Unit Capabilities

(page 2).

These engine generator sets are inherently self regulating

based on engine speed. The engine governor will

automatically adjust itself to the load. No harm to the

generator will result if it is operated with no load connected.

60707-122

Voltage

120V

(Hz)

Recpt.

62.5

126V

60.0

122V

59.0

119V

Proper utilization of the receptacles located on the control

panel is necessary to prevent damage to either the

receptacles or the generator. The generator is a limited

source of electrical power, therefore pay special attention

to the receptacle and generator ratings. The nameplate

rating can be obtained through a single receptacle as long

as the receptacle amperage rating is not exceeded.

HARD WIRING YOUR GENERATOR

Temporary Power

'Hard Wiring' this unit directly into a temporary construction

site electrical system is NOT A SIMPLE DO-IT-YOURSELF

JOB. For your safety all wiring must be done by a qualified

electrician and conform to the National Electric Code and

comply with all state and local codes and regulations.

Check with local authorities before proceeding.

WARNING: PERSONAL DANGER

A fully isolated, double pole double throw manual

transfer switch must be installed any time a generator is

being connected to an existing distribution system.

To connect these units directly to an un-powered, isolated

construction site TemPower panel, have your electrician

connect to the control panel using a 120/240 volt, four wire

twistlock plug (L14-30P). The use of locking receptacles

and locking plugs provides the convenience of quick

disconnect, for moving, while allowing non electrical workers

to safely reconnect the power. In addition they prevent the

plug from being accidentally removed by bumping or

vibration.

Home Standby

If the generator set is connected to existing (electrical)

wiring circuits it is permitted only through a fully isolated

manual transfer switch. The transfer switch prevents

damage to the generator and other circuit components if

main line power is restored while the generator is

connected. Installing a transfer switch also permits the use

of normal fusing.

Many homes and construction sites are wired for at least 60

to 100 Amp entrance service, much greater than the

capacity of these portable generators. When installing the

generator at these sites, a secondary emergency distribution

panel may have to be installed, such as the Emergency

Transfer/Service (ET/S) system available through your

Winco dealer. The emergency distribution panel must be

installed by a licensed electrician according to all applicable

codes. The electrician will move the critical circuits to be

powered during the outage to the emergency panel. Keep

in mind only a limited amount of amperage is available from

the generator set. Some circuit breakers may still have to

be turned off to prevent an overload on the generator during

the initial start up. See the nameplate on your generator for

the amperage capabilities of your unit.

CAUTION: EQUIPMENT DAMAGE

Failure to properly limit and balance the load applied to

the generator will cause the generator to produce low

voltage and may damage the engine generator set. It

may also cause severe damage to the loads connected

to the generator at that time. Improper loading of the

generator set constitutes abuse and will not be covered

by warranty.

Page 5

9160-00