Gage Bilt GB110A/2-4AH Оригинальное руководство по эксплуатации - Страница 12
Просмотреть онлайн или скачать pdf Оригинальное руководство по эксплуатации для Инструменты Gage Bilt GB110A/2-4AH. Gage Bilt GB110A/2-4AH 17 страниц. 20v battery installation tool
Печатать страницуWARNING:
Do not use tool if switch is defective.
WARNING:
Keep installation tool out of the reach of children when not in use.
WARNING:
Maintenance personnel
WARNING:
Disconnect battery before performing maintenance, cleaning or when replacing worn or damaged components.
Severe personal injury may occur if power source is not disconnected.
WARNING:
Read SAFETY DATA SHEET documents for all applicable materials.
WARNING:
Installation tool must be repaired only by qualified specialist personnel and only with original spare parts. This
will ensure the safety of the installation tool is maintained.
The performance of any tool depends upon good maintenance practices. Following these minimal requirements daily will extend the
life of your tool.
*An installation tool that can no longer be switched on or off is dangerous and must be repaired.
*Maintain installation tools with care. Check that moving parts function correctly and do not jam.
*Check that parts are not broken or damaged in such a way that the function of the installation tool is impaired.
*Have damaged parts repaired before using the tool.
*Use installation tool, accessories, attachments, etc. only as described in these instructions.
*Give consideration to the working conditions and the work to be carried out. The use of tools for other than intended applications
can lead to dangerous situations.
*Visual inspection of the installation tool should be done daily by the maintenance personnel.
*Battery charge state should be done daily by the maintenance personnel.
*Cleaning and changing the jaws should be done by the maintenance personnel when the fastener can no longer be set in one stroke.
*Clean out any debris or sealant from jaws after every use.
*Make sure there is no debris inside the nose assembly. You should be able to see through from the front of the nose assembly to
the back of the tool. Remove any obstruction or sealant before use.
*Make sure all pieces of the adapter and nose assembly are tightened properly while using Vibra-tite® to prevent any piece from
unthreading. Failure to do so can cause permanent damage to the tool and will VOID your warranty.
Battery Disposal:
1.
Do not throw the battery (VP1086/VP1357) into the domestic waste, fire or water.
2.
Batteries/ rechargeable batteries are collected and recycled or disposed of in an eco-friendly manner.
For EU countries only:
1.
In accordance with Directive 91/157/EEC, defective old batteries must be recycled. Batteries that can no longer be used can be
returned to your dealer.
Disposal of Installation Tool and Quick Charger:
1.
Installation tools, chargers, accessories and packaging's should be recycled in an eco-friendly manner.
2.
Do not throw tools into the domestic waste.
For EU countries only:
1.
In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment and implementation in national
law, Installation tools must be collected separately and recycled in an eco-friendly manner at the end of the useful life.
Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine
oil, or an equivalent cleaner/lubricant, follow instructions below.
CLEANING
Clean nose assembly daily or as often as needed.
1. Dip nose assembly into mineral spirits or similar solvent
to clean jaws and wash away metal chips and debris.
DO NOT allow jaws to come in contact with other solvents.
DO NOT let jaws soak. Dry jaws immediately.
2. Disassemble nose assembly and use a sharp "pick" to
remove embedded particles from grooves of jaws.
GB110A 20V BATTERY INSTALLATION TOOL
DAILY MAINTENANCE
MUST
read and understand all warnings and cautions.
CLEANING AND LUBRICATING THE CLAMPING JAWS
LUBRICATING
Lubricate nose assembly after each cleaning
and as often as needed.
1. Point nose assembly into oil.
2. Cycle tool 8-10 times and wipe dry.
12
8/18 REV 8/22