Gage Bilt GB730 Руководство по установке - Страница 11
Просмотреть онлайн или скачать pdf Руководство по установке для Инструменты Gage Bilt GB730. Gage Bilt GB730 14 страниц. Installation tool
Также для Gage Bilt GB730: Руководство пользователя (13 страниц)
Печатать страницу
HANDLE
To inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder assy
(730398) first. For complete disassembly, start by removing base cover (704125). Next, holding tool upright, remove four button-head
cap screws (A-928). Lift head cylinder (730398) from handle assy (704132) and set aside o'ring (S832) and gasket (745124). Empty all
hydraulic oil into an approved container and dispose of in accordance with all environmental regulations applicable in your area.
Place piston rod wrench (730151) down into top of power cylinder (730237) and into slot of piston rod assy (730233). While holding
this wrench, remove flexlock nut (400559) using a 7/16" socket wrench. Still holding piston rod wrench (730151), remove air piston
assy (704121) using packing plug wrench (704150), by turning counterclockwise. When air piston assy (704121) is completely free
from piston rod assy (703233), tap or push on the piston rod wrench (730151) to eject air piston assy (704121) from bottom of handle
assy (704132). After removal of air piston assy (704121), slide piston rod assy (730233) back up to the end of its travel. Using packing
plug wrench (704150) remove packing plug (704118). With packing plug (704118) removed, power cylinder (730237) can be removed
by pushing on power cylinder tool (704151) when inserted into top of power cylinder (730237).
To reassemble the handle assy (704132), reverse the above procedure, being certain that all o'rings are properly lubricated before
installation. Torque packing plug (704118) to 45 foot lbs. Attach the seal guide (704152) to the piston rod assy (730233) and tap the
piston rod assy (730233) through the packing plug (704118). Attach air piston assy (704121) and flexlock nut (400559). Torque flexlock
nut to 40 inch lbs. Attach air piston assy (704121) to piston rod assy (730233). With the piston rod assy in the down position, fill oil
passage on top of handle assy (704132) with automatic transmission oil, Dexron III or equivalent. When looking at top of handle assy
(704132), the oil passage is the hole that has a counterbore for o'ring (S832). Replace gasket (745124) and o'ring (S832), just prior to
replacing head cylinder (730398). (See Filling & Bleeding instructions).
AIR VALVE
WARNING:
Disconnect tool from its air source before disassembly.
To disassemble, first disconnect tool from its air source.
into end of valve plug (704145) and pull it out. Using the same procedure, pull out valve spool assy (703142). NOTE: It should never
be necessary to remove valve sleeve (703139) unless the ports in the valve sleeve (703139) are plugged from contaminated air. If
ports are plugged, use needle nose pliers to grasp end of spring (704141), turning clockwise and pulling to dislodge from groove in
casting. NOTE: Valve spring tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be
pulled out using valve sleeve removal tool (704163).
S/N: 2317 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Remove pin (704244) and muffler (704146). Insert valve extractor (S1178)
11
Rev. 2/15