Gage Bilt GB722 Руководство по установке - Страница 10

Просмотреть онлайн или скачать pdf Руководство по установке для Электроинструмент Gage Bilt GB722. Gage Bilt GB722 13 страниц. Installation tool
Также для Gage Bilt GB722: Оригинальное руководство по эксплуатации (20 страниц), Оригинальное руководство по эксплуатации (20 страниц)

HANDLE

To inspect air cylinder bore, remove base cover (704125) and o'ring (S725). Any further disassembly will require removal of the

head cylinder assy (752119) first. For complete disassembly, start by removing base cover (704125) and o'ring (S725). Next, holding

tool upright, remove four button-head cap screws (A-928). Lift head cylinder assy (752119) from handle assy (722132) and set aside

o'ring (S832) and gasket (704129). Empty all hydraulic oil into an approved container and dispose of in accordance with all

environmental regulations applicable in your area. Place piston rod wrench (704149) down into top of power cylinder (722134) into

the hex of piston rod assy (722133). While holding this wrench, remove flexlock nut (400559) using a 7/16" socket wrench. Still

holding piston rod wrench (704149), remove air piston assy (704121) using packing plug wrench (704150), by turning

counterclockwise. When air piston assy (704121) is completely freed from piston rod assy (722133), tap or push on the piston rod

wrench (704149) to eject air piston assy (704121) from bottom of handle assy (722132). After removal of air piston assy (704121),

slide piston rod assy (722133) back up to the end of its travel. Using packing plug wrench (704150) remove packing plug (704118).

With packing plug removed, power cylinder (722134) can be removed by pushing on power cylinder tool (704151) when inserted into

top of power cylinder (722134).

To reassemble the handle assy (722132), reverse the above procedure, being certain that all o'rings are properly lubricated before

installation. Torque packing plug (704118) to 45 foot lbs. Attach the seal guide (704152) to the piston rod assy (722133) and tap the

piston rod through the packing plug (704118). Attach air piston assy (704121) and flexlock nut (400559) to piston rod assy (722133).

Torque to 40 inch lbs. With the piston rod assy (722133) in the down position, fill oil passage on top of handle assy (722132) with

automatic transmission oil, Dexron® III or equivalent, when looking at top of handle assy (722132) the oil passage is the hole that

has a counterbore for (S832) o'ring. Replace gasket (704129) and o'ring (S832), just prior to replacing head cylinder assembly

(752119). (See Filling & Bleeding instructions.)

AIR VALVE

WARNING:

Disconnect tool from its air source before disassembly.

To disassemble, first disconnect tool from its air source.

into end of valve plug (704145) and pull it out. Using the same procedure, pull out valve spool assy (703142). NOTE: It should never

be necessary to remove valve sleeve (703139) unless the ports in the sleeve are plugged from contaminated air. If ports are

plugged, use needle nose pliers to grasp end of spring (704141), turning clockwise and pulling to dislodge from groove in casting.

NOTE: valve spring tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be pulled out

using valve sleeve removal tool (704163).

S/N: 1753 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

Remove pin (704244) and muffler (704146). Insert valve extractor (S1178)

REV. 1/15