Gage Bilt GB150 Руководство - Страница 4

Просмотреть онлайн или скачать pdf Руководство для Заклепочные инструменты Gage Bilt GB150. Gage Bilt GB150 4 страницы. Hydraulic hand riveter
Также для Gage Bilt GB150: Оригинальное руководство по эксплуатации (8 страниц)

Печатать страницу

DO NOT PUMP TOOL WHEN THE SPRING IS NOT IN PLACE, TO RETRACT TOOL WITH NO

SPRING, BRING HANDLES TOGETHER, PUSH THE BUTTON WITH MIDDLE FINGER OR FREE

HAND, PLACE THUMB AND FIRST FINGER OF SAME HAND ON FRONT OF PROTECTIVE SHIELD

AND FORCE IT TO THE FULL RETRACTED POSITION, RELEASE BUTTON AND HANDLES.

GB150 HYDRAULIC HAND RIVETER OPERATING INSTRUCTIONS

1. Place the jaws inside the collet (20323).

2. Place the collet (20323) into the end of spring (50304).

3. Place other end of the spring (50304) over the puller shaft and thread the collet (20323) onto the shaft hand tight until

no threads are showing.

4. Place the holder (10245) over assembly and hand tighten until threads do not show.

5. Choose a nose tip as required (nose tips sold separate see chart) and thread into the holder (10245) hand tight. Re-

verse for disassembly. It may be necessary to pump tool out 2 or 3 strokes before nose tip (nose tips sold sepa-

rately see chart) can be entirely threaded onto the holder (10245).

Operating

Instructions: (with riveting assembly in place per diagram tool is ready to operate)

1. Pump handles 3 or 4 times, holding them together fully on last pump. Push the button while handles are together

and nose assembly will retract.

2. Place rivet stem into the nose tip (nose tips sold separate see chart) and insert rivet into desired hole.

3. Pump handles to install rivet. If more than 10 full pumps are required, re-grip rivet by pushing button and bringing

handles together, slide tool up on rivet stem and finish installing.

4. After stem breaks, push button and bring handles together, point nose tip (nose tips sold separate see chart) down

and rivet stem will fall out, or can be removed by hand.

The Hydraulic system is sealed and oil should not be added. If the tool should be damaged and leaks oil, RETURN IT

TO AN AUTHORIZED SERVICE CENTER.

This unit complies to EN 792-1 Standards

WARNING:

JAW SET - 30426

SPRING - 50304

WARRANTY

Seller warrants that all goods covered by this catalog will conform to

applicable specifications and will replace or repair, F.O.B. our plant, any

goods providing defective from faulty workmanship, or material, for 6 months

from date of shipment.

Said warranty to remain in effect if, and only if, such goods are

used in accordance with all instructions as to maintenance, operation and

use, set forth in manuals and instruction sheets furnished by seller.

Sellers obligation under this warranty shall be limited to the repair

or rework of the goods supplied or replacement thereof, at Seller's option, and

in no case is to exceed the invoice value of said goods. Under no

circumstances will the seller be liable for incidental or consequential damages

or for damages incurred by the buyer or subsequent user in repairing or

replacing defective goods or if the goods covered by this warranty are

reworked or subjected to any type of additional processing.

This warranty is void if Seller is not notified in writing of any

rejections or defects within 6 months after the receipt of the material by the

customer.

THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES

EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY.

HOLDER - 10245

COLLET - 20323

*NOSE TIP

(SOLD SEPARATE SEE CHART)

*BLIND RIVET NOSE TIPS

PART NO.

10231

10232

10425

10211

*Nose tips not supplied with tool

SIZE

3/32"

1/8"

5/32"-3/16"

1/4"

3/16