Gage Bilt GB568 Оригинальное руководство по эксплуатации - Страница 13
Просмотреть онлайн или скачать pdf Оригинальное руководство по эксплуатации для Заклепочные инструменты Gage Bilt GB568. Gage Bilt GB568 20 страниц. Installation tool
Также для Gage Bilt GB568: Оригинальное руководство по эксплуатации (16 страниц)
Печатать страницу
WARNING:
Only qualified and trained personnel shall perform overhaul.
WARNING:
Personnel must read and understand all warnings and cautions.
WARNING:
Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or
wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.
WARNING:
Disconnect tool from its power source before performing overhaul. Severe personal injury may occur if power
source is not disconnected.
WARNING:
Excessive contact with hydraulic oil and lubricants must be avoided (See safety data sheet documents for all
applicable materials)
WARNING:
When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or
rear of tool when installing fastener.
WARNING:
Ensure air hose is securely connected to avoid possible hose whipping (Air Actuated Tools only).
WARNING:
Depress actuator assembly-air (704130) and disconnect from air, with the piston in the rear position, before overhaul.
Severe personal injury may occur if air hose is not disconnected.
downward with head cylinder removed. Hydraulic oil will eject forcibly from handle assembly.
WARNING:
Use only Gage Bilt hydraulic hoses and couplings, or equivalent, rated for 10,000 psi. (689.5 bar) working pressure.
WARNING:
Ensure air hose is securely connected to avoid possible hose whipping (Air Actuated Tools only).
WARNING:
Do not dry cycle or actuate tool without fastener in place. Damage to the nose assembly could occur.
WARNING:
Incorrect stroke will damage the nose assembly.
Note:
•
Dispose of hydraulic oil in accordance with manufacture safety datasheet.
•
All tool materials are recyclable except rubber o'rings, seals and wipers.
•
It is recommended that service tool kit (GB704TK) (see below) be used to facilitate overhaul.
•
Use of SERVICE KIT (722568), which contains a complete set of o'rings, back-up rings, screws, washers and gasket,
can achieve a complete overhaul.
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of
Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and parts lists on pgs. 13-17. Use
extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing
seals, always apply a good lubricant, such as Lubriplate, to the surfaces.
Clean parts in mineral spirits or other o'ring compatible solvent being sure to clean o'ring grooves. Inspect components for scoring,
excessive wear or damage.
1.
When tool life is met, drain hydraulic oil from tool and dispose of the hydraulic oil in accordance with material safety datasheet.
2.
Disassemble tool and remove all rubber o'rings, seals, wipers and hydraulic hoses. All tool materials are recyclable except rubber
o'rings, seals, wipers and hydraulic hoses. Dispose of rubber materials in accordance with the safety data sheet.
GB722/568 INSTALATION TOOL
OVERHAUL
.
GB704TK Service Tool Kit Includes:
Part No.
Description
704149
Piston Rod Wrench Assembly
704151
Power Cylinder Tool Assembly
704150
Packing Plug Wrench Assembly
704152
Seal Guide
704153
Air Bleeder Assembly
704262
Valve Spring Installation Tool Assembly
704163
Valve Sleeve Removal Tool Assembly
S1178
Valve Extractor
TOOL DISPOSAL
13
USE CAUTION
when forcing piston rod assembly
11/21 REV. 5/22