Dynabrade 51824 Руководство - Страница 4

Просмотреть онлайн или скачать pdf Руководство для Сандер Dynabrade 51824. Dynabrade 51824 4 страницы. Hp/right-angle/front exhaust disc sander

Печатать страницу

Disassembly/Assembly Instructions - (continued)

11. Apply Loctite

#567 to threads, and screw 01461 Lock Nut (left-hand threads), onto 02052 Housing.

12. Thread 02052 Housing and 01461 Lock Nut Assembly onto motor housing assembly (right-hand threads), drawing the two assemblies together.

13. Adjust orientation of throttle lever to agree with your grip and comfort level allowing for additional rotation due to tightening to set torque.

14. Using a 34mm crow foot and a torque wrench set at (34 N•m/300 in. - lbs.), secure the gear case housing and lock nut in place.

15. Press 54520 Bearing and then gear onto spindle shaft, making sure drive hexes are aligned.

16. Place 01486 Silencer over spindle shaft at threaded end.

17. Slip bottom wick over spindle shaft, then place top wick over spindle shaft.

18. Insert spindle shaft assembly into 02052 Housing.

19. Torque 02035 Lock Nut to 23 N•m/200 in. - lbs.

20. Shim spindle assembly using shims if required.

Note: When assembling angle-head assembly onto the motor housing, make sure flats on the wicks are both facing the pinion or tool will not run.

Tool Assembly is complete. Please allow 30 minutes for adhesives to cure before operating tool.

Important: Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool for

30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor. Motor should now be tested for proper operation at

90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use.

Loctite

is a registered trademark of Loctite Corp.

96179 Motor Tune-Up Kit

•

Includes assorted parts to help

maintain and repair motor.

Dynaswivel

•

Swivels 360° at two locations which allows an

air hose to drop straight to the floor, no matter

how the tool is held.

94300 1/4" NPT

Dynabrade Angle Gear Oil

•

Specifically formulated to saturate wick system in right

angle gear head.

•

Easy to apply using Dynabrade P/N 95541 Oil Gun.

Apply 3 plunges every 8 hours of operation into tools

lubrication fitting.

95848: 2 oz. tube

95849: 10 oz. tube

Expect a

gear life of

500 hours

minimum,

with proper

lubrication.

Visit Our Web Site: www.Dynabrade.com

DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

DYNABRADE EUROPE S.àr.l.,

Optional Accessories

Apply 3 plunges

into lubrication

fitting every

8 hours of

operation.

Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1

52296 Repair Collar

•

Specially designed collar for use in vise to prevent damage

to valve body of tool during disassembly/assembly

Dynabrade Air Lube

•

Formulated for pneumatic equipment.

•

Absorbs up to 10% of its weight in water.

•

Prevents rust and formation of sludge.

•

Keeps pneumatic tools operating longer

with greater power and less down time.

95842: 1pt. (473 ml)

95843: 1gal. (3.8L)

Email: Customer.Service@Dynabrade

DYNABRADE

PRINTED IN USA