GREAT PLAINS 1200-4800TM Краткое руководство по эксплуатации - Страница 4

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Сельскохозяйственное оборудование GREAT PLAINS 1200-4800TM. GREAT PLAINS 1200-4800TM 6 страниц. Hydraulic leveling kit

Печатать страницу
4
Hydraulic Remote
586-530A Hydraulic Remote Tmax
Leveling Kit S/N GP-C6544-
Part Number
586-528V
HOSE KIT LEVEL - TMAX
FITTINGS KIT - LEVEL -
586-529V
TMAX
MANUAL TMAX HYD
586-541M
REMOTE LEVEL
586-849D
589-222D
LEVEL GUAGE BRACKET
589-487H
LEVEL INDICATOR
CABLE TIE.19X7.25 1.75D
800-112C
802-152C
HHCS 1/4-20X2 GR5
803-006C
NUT-HEX 1/4-20 PLT
WASHER LOCK SPRING 1/4
804-006C
810-599C
CYL 4X3X1.50 ROD (TIE
810-626C
858-059C
TM LEVEL DECAL
Assembly Instructions
Note: Move machine to level ground and lower machine
until pressure is off of hitch turnbuckle (3).
Refer to Figure 4
1.
Remove the 1" top lock nuts from the 1 x 6, Gr. 8
special thread bolt (1) and 1 x 8 Gr. 8, special
thread bolt (2).
2.
Remove bolts (1), (2) and turnbuckle (3) and the
bolt (4) from cylinder clevis.
3.
Install base end of the 810-626C cylinder (6) with
the 1 x 6, Gr. 8 special thread bolt (1) secure with
the same 1 top lock nut. Torque bolt to 910ft-lb.
4.
Install rod end of the 810-626C cylinder (6) and the
589-487H level indicator (7) with the 1 x 8, Gr. 8
special thread bolt (2). Secure with the same 1" top
lock nut. Torque bolt (2) to 910ft-lb. Re- install the
3
bolt (4) to cylinder clevis (6) and small hole of
8
589-487H level indicator (7). Torque bolt (4) to 31ft-
lb.
5.
Remove the two nuts (8) from rod end of cylinder (6)
and install the 589-222D level gauge bracket (9) in
position shown. Re-install the two nuts (8). Tighten
nuts (8) snug.
586-541M
Description
VALVE BRACKET
50LB
PLT
LOCK VALVE
ROD
Hydraulic Remote Leveling
Refer to Figure 3
Qty.
1
1
1
1
1
1
2
3
3
3
1
1
1
Null4:
6.
Install the 586-849D valve bracket (5) and 810-
599C lock valve (10) with three, 802-152C,
bolts (11),
3
valve bracket to the hitch using the 1 x 6, Gr. 8 spe-
8
cial thread bolt (1) and the 1" top lock nut that also
attaches the cylinder to the hitch.
Null4:
Note: Be sure ports in cylinders, valves, all fittings and
hose ends are clean before installing fittings if fit-
tings are not installed. If fittings and hoses are con-
nected to valve and cylinder go onto step 10.
7.
Install two, orrifice plates (12) into cylinder ports
(groove side out). Install two, 90 degree elbows (13)
into cylinder ports, turn to desired angle for best
hose routing and tighten jam nut.
8.
Install three straight fittings (14) into both front ports
and rear right hand port (10) and one 90 degree
elbows (13) into the rear left hand port of lock valve.
Tighten fittings.
Great Plains Manufacturing, Inc.
Figure 3
Hydraulic Remote Leveling
1
1
lock washers and
4
4
43122
1
x 2
4
nuts. Install the
08/15/2019