Dynabrade 52660 Руководство по безопасности, эксплуатации и техническому обслуживанию - Страница 3
Просмотреть онлайн или скачать pdf Руководство по безопасности, эксплуатации и техническому обслуживанию для Шлифовальный станок Dynabrade 52660. Dynabrade 52660 8 страниц. 1hp die grinder
Important: A Preventative Maintenance Program is recommended whenever portable planetary geared die grinders are used.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.
• All Dynabrade Rotary Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties. Dynabrade recommends the following:
11411 Air Filter-Regulator-Lubricator (FRL) – Provides accurate air pressure regulation and two stage filtration of water contaminants. Operates 55
SCFM/1,558 LPM @ 100 PSIG with 1/2" NPT female ports.
• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.
• Lubricate the planetary gears through the grease fitting(s) located in the gear/planetary cover. Apply 2-3 plunges* for every 50 hours of use, to achieve
maximum gear life. (*order 95542 Grease and 95541 Gun)
Routine Preventative Maintenance:
• DO NOT disassemble the governor for any reason. Reorder correct speed – governor assembly (See Assembly Breakdown) and recheck free speed of
tool with a tachometer.
• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
• A Motor Tune-Up Kit (P/N 96532) is available which includes high wear and medium wear motor parts.
• Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification information i.e.:
Model#, S/N, and RPM. (See Assembly Breakdown)
• Blow air supply hose out prior to initial use.
• DO NOT carry tool by air hose or near the tool throttle lever.
• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
• Periodically remove the collet insert and clean the inside diameter and slots from debris to keep accessories secure and reduce vibration.
• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
• Use of tool rests, hangers and/or balancers is recommended.
• Protect grinding wheels from exposure to water, solvents, high humidity, freezing temperatures and extreme temperature changes.
• DO NOT USE grinding wheels that have been dropped or show signs of cracks, nicks or other defects.
• Store accessories in protective racks or compartments to prevent damage.
Model
Motor
Number
HP (W)
52660
1 (744)
52661
1 (744)
52662
1 (744)
52663
1 (744)
52680
1 (744)
52681
1 (744)
52682
1 (744)
52683
1 (744)
Additional Specifications: Air Inlet Thread 3/8" NPT • Hose Size 3/8" or 10mm • Air Flow Rate Based At Max HP. • Air Pressure 90 PSIG Max
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. Dirt and water often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty
obligation is contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a
lack of lubrication during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Maintenance Instructions
Machine Specifications
Motor
Sound
Maximum Air Flow
RPM
Level
CFM/SCFM (LPM)
950
80 dB(A)
6/43 (1218)
1,800
76 dB(A)
5/34 (963)
3,400
80 dB(A)
6/43 (1218)
4,500
80 dB(A)
6/41 (1161)
950
80 dB(A)
6/43 (1218)
1,800
76 dB(A)
5/34 (963)
3,400
80 dB(A)
6/43 (1218)
4,500
80 dB(A)
6/41 (1161)
One Year Warranty
®
).
Spindle
Air Pressure
Thread
PSIG (Bars)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
1/2"-20 Male
90 (6.2)
Notice
3
Weight
Length
Pound (kg)
Inch (mm)
Inch (mm)
3.5 (1.6)
13-3/4 (384)
1-7/8 (48)
2.8 (1.3)
11-1/8 (284)
1-7/8 (48)
3.1 (1.4)
12-1/2 (317)
1-7/8 (48)
3.1 (1.4)
12-1/2 (317)
1-7/8 (48)
3.5 (1.6)
13-3/4 (384)
1-7/8 (48)
2.8 (1.3)
11-1/8 (284)
1-7/8 (48)
3.1 (1.4)
11-1/8 (284)
1-7/8 (48)
3.1 (1.4)
11-1/8 (284)
1-7/8 (48)
Height