Dynabrade Electric Dynafile II Инструкции по безопасности, эксплуатации и техническому обслуживанию - Страница 3
Просмотреть онлайн или скачать pdf Инструкции по безопасности, эксплуатации и техническому обслуживанию для Инструменты Dynabrade Electric Dynafile II. Dynabrade Electric Dynafile II 8 страниц. Abrasive belt tool
Также для Dynabrade Electric Dynafile II: Руководство (4 страниц)
Печатать страницу
Abrasive Belt/Contact Arm Change Instructions
To Change Belt:
1. Disconnect tool from the power source.
2. Loosen the 15329 Screw and remove the 15312 Belt Guard.
3. Pull back the 15306 Tension Arm and remove the abrasive belt.
4. Install a new abrasive belt, and the 15312 Belt Guard.
5.
Adjust belt tracking by turning 95218 Adjustment Knob to the left or right
accordingly, so as abrasive belt rides evenly over contact arm.
6.
Connect tool to power source.
Housing Angle Adjustment: To pivot the 15372 Belt Housing Assembly, use a 9/64" hex key to loosen the 95311 Screw. Pivot the belt housing assembly to the
desired position and retighten screw.
Installing Side Handle: The 89351 Side Handle may be installed on either side of the gearbox housing, for right or left hand operation. To install, thread side handle
into socket and tighten securely.
Abrasive Types and Cloth Polishing Belts
Aluminum Oxide
The most widely used abrasive grain. This tough durable synthetic is used for
grinding and deburring high carbon steels, general metalworking and for
sanding certain hardwoods.
Ceramic Aluminum Oxide
Synthetic grain two-to-three times tougher than conventional aluminum oxide.
Silicon Carbide
Excellent for sanding primer and sealer. This sharp, fast-penetrating grain is
used for sanding soft materials such as plastics and fibrous wood.
Alumina Zirconia
Effective for coarse stock removal of metal and wood. This synthetic grain has
self-sharpening characteristics and provides continuous new cutting edges for
longer life and greater efficiency.
All abrasive accessories may be found in the most current Dynabrade
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have
been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety
practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal
performance. Normally wearable parts such as bearings, contact wheels, brushes, gears, etc., are not covered under this warranty.
To Change Contact Arm Assembly:
1. Disconnect the tool from the power source.
2. L oosen the 15329 Screw and remove the 15312 Belt Guard.
3. Pull back the 15306 Tension Arm and remove the abrasive belt.
4. Loosen the 95218 Adjustment Knob to remove the contact arm assembly.
5. Install the desired contact arm assembly (Ref pg. 6) so that the tab on the
end of the arm faces toward the 15306 Tension Arm.
6. Fasten the contact arm assembly in place with the 95218 Adjustment Knob.
7. Install a new abrasive belt, and the 15312 Belt Guard.
8. Adjust the belt tracking by turning the 95218 Knob.desired position and
retighten screw.
Abrasive Impregnated Non-Woven Nylon
A non-woven synthetic fiber and an abrasive mineral are bonded together to
form a tough, open web that is chemically resistant and long-lasting. This web
design allows controlled conformable contact to workpiece contours, corners
and edges. The product wears away slowly, exposing new abrasive leaving a
uniform, consistent surface. It also conditions surfaces without removing or
damaging the base material and is excellent for deburring, cleaning, blending
and final finishing of metal, wood and plastics. It is available in many forms such
as belts, discs and wheels. Various mineral grades are available
ranging from very coarse to ultra-fine.
Cloth Polishing Belts
Used on power tools in conjunction with Dynuba
result is brilliant cut, color and luster on metals such as stainless steel,
aluminum, copper and brass.
One Year Warranty
3
(Ref pg. 4)
®
polishing compounds. The
®
Catalog and abrasive literature.