ADEMCO Ademco VISTA-20P Руководство по программированию - Страница 4
Просмотреть онлайн или скачать pdf Руководство по программированию для Система безопасности ADEMCO Ademco VISTA-20P. ADEMCO Ademco VISTA-20P 17 страниц. Programming auto arming and disarming schedules
Также для ADEMCO Ademco VISTA-20P: Руководство по быстрой установке (2 страниц), Руководство пользователя (20 страниц), Руководство по программированию (17 страниц), Краткое руководство по эксплуатации (6 страниц), Руководство по быстрой установке (2 страниц), Руководство по быстрой установке (2 страниц), Руководство по программированию (2 страниц), Краткое руководство (2 страниц)
Печатать страницу
∗ ∗ ∗ ∗ 49
Split/Dual Reporting
0 = Standard/backup reporting only (all to primary)
Primary Phone No.
1 = Alarms, Restore, Cancel
2 = All except Open/Close, Test
3 = Alarms, Restore, Cancel
4 = All except Open/Close, Test
5 = All
∗ ∗ ∗ ∗ 50
Burglary Dialer Delay
Delay Time:
0 = no delay UL: must be "0"
1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds
SIA Guidelines: delay must be minimum of 30 seconds
V20PSIA/V15PSIA:
Delay Time: 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds
Delay Disable:
0 = use delay set in entry 1
1 = dial delay disabled for zones listed in zone list 6 (use zone list 6
to enter those zones that require dial delay to be disabled;
these zones ignore the setting in entry 1)
UL: Dial delay plus entry delay must not exceed one minute; use zone
list 6 to disable dial delay from appropriate zones, if necessary.
∗ ∗ ∗ ∗ 53
SESCOA/Radionics Select
0 = Radionics (0-9, B-F); enter "0" for all non-SESCOA formats
1 = SESCOA (0-9 only reporting)
∗ ∗ ∗ ∗ 54
Dynamic Signaling Delay
Select delay from 0 to 225 secs, in 15-sec increments.
0 = no delay (both signals sent); 1 = 15 secs; 2 = 30 secs, etc.
UL: Grade AA must be "0;" Grade A must be "15" max
∗ ∗ ∗ ∗ 55
Dynamic Signaling Priority
0 = Primary Dialer first; 1 = Long Range Radio first.
For UL Commercial Burglary installations that use a DACT and LRR,
this field must be "0".
∗ ∗ ∗ ∗ 56
∗ ∗ ∗ ∗ 57
∗ ∗ ∗ ∗ 58
Menu Modes
,
,
These are Menu Mode commands, not data fields, for Zone Programming,
Function Key Programming, and Expert Mode Zone Programming respectively.
See page 2 and respective sections later in this document.
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (∗ ∗ ∗ ∗ 59 thru
∗ ∗ ∗ ∗ 68, *70 thru ∗ ∗ ∗ ∗ 76, and ∗ ∗ ∗ ∗ 89):
For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, #+10 for
0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.
A 0 ( not #+10) in the first box will disable a report. A 0 ( not #+10) in the
second box will result in automatic advance to the next field.
For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits)
for 1–9, 0, or B–F, as described above.
A 0 ( not #+10) in the second box will eliminate the expanded message for
that report. A 0 ( not #+10) in both boxes will disable the report.
For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the first
box, to enable zone to report (entries in the second boxes are ignored).
A 0 ( not #+10) in the first box disables the report.
UL: see installation instructions for requirements
SYSTEM STATUS REPORT CODES
∗ ∗ ∗ ∗ 59
Exit Error Alarm Report Code
See above for entries.
V20PSIA/V15PSIA:
∗ ∗ ∗ ∗ 60
Trouble Report Code
∗ ∗ ∗ ∗ 61
Bypass Report Code
∗ ∗ ∗ ∗ 62
AC Loss Report Code
∗ ∗ ∗ ∗ 63
Low Bat Report Code
∗ ∗ ∗ ∗ 64
Test Report Code
Use Scheduling mode to set periodic test reports, or use the following
key commands:
installer code +[#] + [0] + 0 = test report sent every 24 hours
installer code +[#] + [0] + 1 = test report sent once per week
installer code +[#] + [0] + 2 = test report sent every 28 day
Each mode sets schedule 32 (VISTA-20P) or schedule 08 (VISTA-15P)
to the stated repeat option; first test report sent 12 hours after command.
∗ ∗ ∗ ∗ 65
Open Report Code
[0]
2nd Phone No.
Others
Open/Close, Test
All
All
All
[2,0]
Delay Time
V20PSIA/V15PSIA
Delay Disable
[0]
[0]
[0]
( ✱ 59– ✱ 68)
[0]
[1] Always enabled.
[00]
|
[00]
|
[00]
|
[00]
|
[00]
|
[0,0,0]
Part. 1
Part. 2 Common
∗ ∗ ∗ ∗ 66
Arm Away/Stay Rpt Code
Away
Stay
Away
Part. 1
∗ ∗ ∗ ∗ 67
RF Trans. Low Bat Report Code
UL: must be enabled if wireless devices are used
∗ ∗ ∗ ∗ 68
Cancel Report Code
V20PSIA/V15PSIA:
∗ ∗ ∗ ∗ 69
Recent Closing Report Code
V20PSIA/V15PSIA:
Always enabled.
Field does not apply to other controls.
RESTORE REPORT CODES ( ✱ 70 – ✱ 76)
∗ ∗ ∗ ∗ 70
Alarm Restore Rpt Code
∗ ∗ ∗ ∗ 71
Trouble Restore Rpt Code
∗ ∗ ∗ ∗ 72
Bypass Restore Rpt Code
∗ ∗ ∗ ∗ 73
AC Restore Rpt Code
∗ ∗ ∗ ∗ 74
Low Bat Restore Rpt Code
∗ ∗ ∗ ∗ 75
RF Trans. Lo Bat Rst Rpt Code
UL: must be enabled if wireless devices are used
∗ ∗ ∗ ∗ 76
Test Restore Rpt Code
OUTPUT AND SYSTEM SETUP (
∗ ∗ ∗ ∗ 77
Daylight Savings Time
Start/End Month
0 = Disabled
1-12 = January-September (1 = Jan, 2 = Feb, etc)
#+10 = October; #+11 = November; #+12 = December
∗ ∗ ∗ ∗ 78
Daylight Savings Time
Start/End Weekend
0 = disabled; 1 = first; 2 = second; 3 = third; 4 = fourth;
5 = last; 6 = next to last; 7 = third to last
∗ ∗ ∗ ∗ 79
*80
*81
*82
Menu Modes
,
,
,
These are Menu Mode commands, not data fields, for Output Device Mapping,
Output Programming, Zone List Programming, and Alpha Programming
respectively. See page 2 and their respective sections in the Installation and
Setup Guide for procedures.
∗ ∗ ∗ ∗ 84
Auto Stay Arm
0 = no; 1 = partition 1 only; 2 = partition 2 only; 3 = both partitions
∗ ∗ ∗ ∗ 85
Cross Zone Timer
This option not for use in UL installations.
(assign cross zones on zone list 4, using *81 Menu mode)
0 = 15 seconds
1 = 30 seconds
2 = 45 seconds
3 = 60 seconds
4 = 90 seconds
5 = 2 minutes #+11 = 7 min
∗ ∗ ∗ ∗ 86
Cancel Verify Keypad Display
0 = no "alarm canceled" display
1 = display "Alarm Canceled" when system is disarmed after an alarm
has occurred. (To clear the "ALARM CANCELED" display, the
user must enter the security code + OFF again.)
∗ ∗ ∗ ∗ 87
Misc. Fault Delay Time
(used with Configurable Zone Types "digit 6")
0 = 15 seconds
1 = 30 seconds
2 = 45 seconds
3 = 60 seconds
4 = 90 seconds
5 = 2 minutes
UL: may only be used on non-burglar alarm/ non-fire alarm zones
when used in fire and/or UL burglar alarm installation
– 4 –
[0,0,0,0,0,0]
Stay
Away
Stay
Part. 2
Common
[00]
[00]
[10] Report enabled.
[11]
[00]
[00]
[00]
[00]
[00]
[00]
✱
✱
77 –
93)
[4][10]
[1][5]
6 = 2-1/2 min
#+12 = 8 min
7 = 3 min
#+13 = 10 min
8 = 4 min
#+14 = 12 min
9 = 5 min
#+15 = 15 min
#+10 = 6 min
6 = 2-1/2 min
#+12 = 8 min
7 = 3 min
#+13 = 10 min
8 = 4 min
#+14 = 12 min
9 = 5 min
#+15 = 15 min
#+10 = 6 min
#+11 = 7 min
|
|
|
[0]
|
|
|
|
|
|
|
|
[3]
[0]
[1]
[0]