Dynabrade 53073 Важные инструкции по эксплуатации, обслуживанию и безопасности - Страница 4

Просмотреть онлайн или скачать pdf Важные инструкции по эксплуатации, обслуживанию и безопасности для Аксессуары для электроинструментов Dynabrade 53073. Dynabrade 53073 4 страницы. Air motor and machine parts, 3,200 rpm

Печатать страницу
Disassembly/Assembly Instructions (continued)
Valve Body Assembly:
1. Insert 01469 Regulator with o-rings and valve stem in place into valve body. Secure with 95558 Retaining Ring.
2. Secure valve body in vise using 52296 Repair Collar with air inlet facing upwards. Insert 01464 Seal.
3. Line up hole in valve stem with hole in housing (looking past brass bushing). Insert 01472 Tip Valve so that the metal pin passes through the hole in the
valve stem. Install 01468 Spring (small end towards tip valve).
4. Place felt muffler in 94522 Muffler Cap. Install 94521 Muffler Base onto muffler cap.
5. Install 95438 O-Ring into groove on muffler base. Place 95375 O-Ring and 94526 Spacer into recessed area of muffler cap.
6. Slip 94523 Inlet Adapter through muffler assembly and install 95711 Retainer Ring into groove on inlet adapter.
7. Install 01564 Air Control Ring into valve body housing.
8. Apply Loctite
®
#567 PST Pipe Sealant to threads of 94523 Inlet Adapter and install entire muffler assembly onto valve body.
Torque 23 N•m/200 in. - lbs.
9. Replace air fitting. Secure inlet adapter with a wrench before tightening air fitting.
10. Install throttle lever and 12132 Pin.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the
tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet
with throttle lever depressed. Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
is a registered trademark of Loctite Corp.
®
Dynaswivel
•
Swivels 360° AT TWO PIVOT POINTS allowing the air hose to
drop directly to the floor while providing superb tool handling.
•
New 94300 1/4" NPT, non-marring composite construction.
Grease
•
Multi-purpose grease for all types of bearings, cams, gears.
•
High film strength; excellent resistance to water, steam, etc.
•
Workable range 0˚ F to 300˚ F
95541: Push-Type Grease Gun (one-handed operation).
95542: 10 oz. (283.5 g) tube.
50971 Lock Ring Tool
•
Lock Ring Tool has a 3/8 in. square socket
for use with 3/8 in. drive; breaker bar,
ratchet head, or torque wrenches.
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2004
Optional Accessories
®
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
96173 Motor Tune-Up Kit
•
Includes assorted parts to help maintain
and repair motor.
52296 Repair Collar
•
Specially designed collar for use in vise
to prevent damage to valve body
housing during disassembly/assembly.
Open-End Wrenches
95262 – 14 mm open-end.
95281 – 19 mm open-end.
DYNABRADE
PRINTED IN USA
®