Dynabrade 61375 Инструкция по эксплуатации
Просмотреть онлайн или скачать pdf Инструкция по эксплуатации для Аксессуары для электроинструментов Dynabrade 61375. Dynabrade 61375 5 страниц. 8" random orbital head
Печатать страницу8" Random Orbital Head Assemblies
Accessory:
61374 – Accepts 5/8"-11 Spindle Thread
– 3,200 Maximum RPM
61375 – Accepts M14 x 2 Spindle Thread
– 3,200 Maximum RPM
Carefully Read all instructions before operating or servicing any Dynabrade
Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written
consent from Dynabrade, Inc.
Accessory Intent: Random Orbital Head Assemblies are ideal for expanding the versatility of any equipt 5/8"-11 or M14 x 2 spindle power tool.
Do Not Use accessory for anything other than random orbital buffing/polishing applications.
This accessory is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.
Training: Proper care, maintenance, and storage of your tool/accessory will maximize their performance.
• Employer's Responsibility – Provide power tool operators with safety instructions and training for safe use of tools and accessories.
Accessory Selection:
• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool or accessory RPM rating.
• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.
• Follow tool/accessory specifications before choosing size and type of accessory.
Warning: Always wear personal protective equipment.
Caution: After installing the accessory, before testing or use and/or after reassembling tool, the Random Orbital Head Assembly must be started at a reduced
speed to check for good balance. Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to
insure safe operation.
• Please refer to original manufacturers tool specifications for maximum RPM rating and any other safety requirements.
Power Tool RPM must never exceed accessory RPM rating of 3,200 RPM.
• Check accessory for details on maximum operating speed, special mounting instructions are provided on page 2.
• Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
• Keep hand and clothing away from working end of the power tool.
• Be sure that any loose clothing, hair and all jewelry is properly restrained.
• BEFORE MOUNTING AN ACCESSORY, after all tool repairs and whenever a Random Orbital Head Assembly is issued for use, check tool RPM/OPM
(speed) with tachometer while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool housing, or operating improperly,
the tool must be serviced and corrected before use.
• Disconnect tool from power supply when changing accessories.
• Ensure that self-fixing and hook accessories are mounted concentrically.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris. Potentially explosive atmospheres can be caused
by dust and fumes resulting from buffing or polishing. Always use dust extraction or suppression systems which are suitable for the material
being processed.
• Proceed with caution in unfamiliar surroundings. Hidden hazards may exist, such as electricity or other utility lines.
• When applicable use a vise or clamping device to hold work piece firmly in place.
• Work may generate hazardous dust.
• Do not apply excessive force on tool/accessory or apply "rough" treatment to it.
• Always work with a firm footing, posture and proper lighting.
• Ensure that sparks and debris resulting from work do not create a hazard.
REPORT TO YOUR SUPERVISOR ANY CONDITION OF THE TOOL, ACCESSORIES, OR OPERATION YOU CONSIDER UNSAFE.
Assembly Conversion Instructions
SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL
SAFETY INSTRUCTIONS
OPERATING INSTRUCTIONS
®
Accessory.
Parts Page Reorder No. PD06•29
Effective August, 2006
Supersedes PD05•45
3/4" Random
Orbit Motion