2gig Technologies 2GIG-SHKDW1-345 Инструкции по установке - Страница 3

Просмотреть онлайн или скачать pdf Инструкции по установке для Аксессуары 2gig Technologies 2GIG-SHKDW1-345. 2gig Technologies 2GIG-SHKDW1-345 4 страницы. Shock/door/window contact sensor

Печатать страницу

Shock/Door/Window Contact | Installation Instructions

Calibrating Magnet Detection

When magnetic detection is first enabled, the RED LED will

blink to indicate that it is not calibrated. THE SENSOR MAGNET

CALIBRATION MUST BE COMPLETED TO OPERATE PROPERLY.

IF NOT CALIBRATED THE SENSOR WILL NOT TRANSMIT OPEN/

CLOSE INFORMATION TO THE CONTROL PANEL.

To calibrate the sensor:

Mount the sensor and magnet in it's final location as instructed

earlier in this document.

Close the door or window.

Press the Program button.

LED will start blinking ORANGE.

Open the door or window completely.

Press the Program button again.

LED will start blinking green

Fully close door or window and press the Program Button within

10 seconds to complete the calibration process..

LED will illuminate green for 2 seconds and then turn off and the

calibration is complete.

NOTE: If Magnet Detection is turned off then back on or if the battery

is removed or replaced, the sensor will lose the Magnet Calibration

setting and will have to be re-calibrated.

Installer Test Mode

To enter Installer Test Mode, remove the top housing from the sensor.

In this mode the LED will blink to indicate specific conditions.

Event

LED Color

Shock Detected

Red

Magnetic Detection

Green

Magnetic Tamper

Orange

Magnetic Calibration Required Red

Finalizing the Installation

Figure 4. Replacing Sensor Cover

1 Tilt the cover to align tab C through slot D.

2 Close the cover down, and press down until tab A snaps into slot B.

Shock Detection System Test - Glass Mounted

Firmly tap the glass twice with a hard plastic object (screwdriver

handle) within 12 inches of the sensor. Verify that the shock event

was received by the panel. It may take up to 2 seconds for the panel

to receive the notification.

NOTE: Do not strike the surface hard enough to break the glass.

Duration

ON for 8 seconds

Single Blink

Double Blink

Inserting and Replacing the Batteries

To insert or replace the batteries:

1 Press in the Retaining Tab (A) and gently swing the top of the

sensor up and off the base.

2 Place a small non-metal object in the slot on the side of the sensor

(see Part C,D in Figure 2, Shock / Door / Window Contact and

Battery Compartment).

3 Carefully push the battery out through the Battery Access slot.

Figure 5. Remove/Replace Battery

IMPORTANT: Always dispose and/or recycle used batteries in

accordance with the hazardous waste recovery and recycling

regulations for your location. Your city, state, or country may also

require you to comply with additional handling, recycling, and disposal

requirements.

1 Insert the replacement battery in the compartment. The positive (+)

sign on the battery should be facing down and the negative (–) side

facing up.

2 The Green LED will illuminate for 2 seconds as the Device powers up.

3 Replace the top case (see Finalizing the Installation, above).

WARNING: Failure to follow these warnings and instructions can lead

to heat generation, rupture, leakage, explosion, fire, or other injury, or

damage. Do not insert the battery into the compartment in the wrong

direction. Always replace the battery with the same or equivalent type.

Never recharge or disassemble the battery. Never place the battery in

fire or water. Always keep batteries away from small children. If batter-

ies are swallowed, promptly see a doctor.

Restore Factory Settings

Press and hold the program button for more than 10 seconds:

● Release the program button after the Orange LED flashes three times.

● Press and release the program button once more to confirm that

factory defaults are to be restored. If this is not done within 5

seconds, the reset function will be terminated with no change to the

programmed settings.

The Red LED will flash as per the programmed shock sensor setting then

the Green LED will flash per the programmed Magnet Detection setting.