GREAT PLANES S.E.5a Руководство по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Самолеты GREAT PLANES S.E.5a. GREAT PLANES S.E.5a 20 страниц.
Печатать страницу
2. You must assemble the model according to the
instructions. Do not alter or modify the model, as doing so
may result in an unsafe or unflyable model. In a few cases
the instructions may differ slightly from the photos. In those
instances the written instructions should be considered
as correct.
3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in first-
class condition.
5. You must correctly install all R/C and other components so
that the model operates correctly on the ground and in the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not flown this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for your
first flights. If you're not a member of a club, your local hobby
shop has information about clubs in your area whose
membership includes experienced pilots.
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and flyability of your finished model depends on
how you build it; therefore, we cannot in any way
guarantee the performance of your completed model, and
no representations are expressed or implied as to the
performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
BATTERY CHARGER OPTIONS
The Great Planes S.E.5a EP ARF is designed for use with
LiPo batteries only. All LiPo batteries require a charger
specifically designed for charging LiPo batteries. The use of
a charger not designed for charging LiPo batteries will result
in damage to the batteries and possibly a fire.
We recommend the use of the Great Planes Triton
Peak Charger (GPMM3150), the ElectriFly
(GPMM3010) or for charging more than one battery at a
time the ElectriFly PolyCharge4 (GPMM3015).
In addition to the items listed in the " BATTERY CHARGER
OPTIONS" section, the following is the list of hardware and
accessories required to finish the S.E.5a EP ARF. Order
numbers are provided in parentheses.
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
In addition to common household tools and hobby tools, this
is the "short list" of the most important items required to build
the S.E.5a EP ARF. Great Planes Pro
are recommended.
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Here is a list of optional tools mentioned in the manual that
will help you build the S.E.5a EP ARF.
❏
❏
❏
❏
❏
❏
❏
™
DC
❏
™
DC PolyCharge
™
❏
3
ADDITIONAL ITEMS REQUIRED
Hardware & Accessories
4-Channel radio with four micro servos
(1) ElectriFly SS-25 25 amp brushless ESC (GPMM1820)
(1) ElectriFly 3.5mm Bullet
(female) connector adapter (GPMM3122)
(1) ElectriFly 1250mAh LiPo 3-cell battery (GPMP0823)
(1) Futaba
®
R114F 4-channel FM receiver
(FUTL0443, FUTL0442)
(2) 12" [305mm] Futaba extensions (FUTM4507)
(1) Futaba "Y-harness" (FUTM4130)
(1) ElectriFly RimFire C28-30-950 brushless
motor (GPMG4560)
(1) 10x4.5 Prop (GPMQ6660)
(1) 3mm Prop adapter (GPMQ4959)
Adhesives & Building Supplies
1 oz. [28g] Thin Pro CA (GPMR6002)
#1 Hobby knife (HCAR0105)
#11 Blades (5-pack, HCAR0211)
Medium T-pins (100, HCAR5150)
Builder's Triangle Set (HCAR0480)
K & S #801 Kevlar
®
thread or string (for stab alignment)
Pliers
Wire cutter
Top Flite
®
MonoKote
®
heat gun (TOPR2000)
Clear tape
Optional Supplies & Tools
Stick-on segmented lead weights (GPMQ4485)
Top Flite MonoKote sealing iron (TOPR2100)
Top Flite Hot Sock
™
iron cover (TOPR2175)
2 oz. [57g] Spray CA activator (GPMR6035)
CA applicator tips (HCAR3780)
CA debonder (GPMR6039)
Robart Super Stand II (ROBP1402)
CG Machine
™
(GPMR2400)
Precision Magnetic Prop Balancer
™
(male) to 2mm Bullet
™
CA and Epoxy glue
™
(TOPQ5700)