Automatic Technology Australia EasyRoller GDO-4 Инструкции по установке и руководство пользователя - Страница 12

Просмотреть онлайн или скачать pdf Инструкции по установке и руководство пользователя для Открыватель двери гаража Automatic Technology Australia EasyRoller GDO-4. Automatic Technology Australia EasyRoller GDO-4 16 страниц.

Печатать страницу

lnstallation

cont...

8.3

DELETING

THETRANSMITTERS CODE FROMTHE

CONTHOLLERS

RECEIVER

lf you only want

to delete

one transmitter

code

stored

then

use step 8.3a

d. Use

step

B.3e

h if you want

to delete

all

the

stored transmitter

codes.

(a)

Select the

transmitte(s)

you want

delete

from

memory.

(b)

Press

and

hold

the

Blue

Code Set

Button on

the

Control

Panel

(see

Fig. 20).

(c)

Press the Transmitter Button for approximately

two

seconds.

Pause for

two

seconds. Press the

transmitters

Button again for

approximately

two

seconds.

(d)

Release

the

Code

Set

Button.

The

code

should

now be deleted.

Confirm this

by pressing the

transmitter

button

to see if

it can

operate

the

door.

Turn

the

Power Off to

the

Drive

Unit.

Press

and

hold

the

Blue Code

Set

Button on

the

Control panel.

Turn

the

Power back On again.

Release

the Code

Set Button after

three

seconds. All

the

Stored

codes

should

be now deleted.

Confirm this

trying to

operate the

door

by pressing

one

of the deleted transmitters.

(e)

(s)

(h)

FITTING WALL SWITCH

(a)

Remove

the front

cover from the Wall Switch. Take note of the

orientation of

the

Switch,

the Open/Close

Button must be

the top

when

mounting to the wall.

(b)

Locate the Wall Switch in a convenient position. Make sure

thai

you

mount

the Switch

higher

than

a child

can

reach

and

position

where

the door

is clearly visible.

(c)

Connect the

three

wires, and secure to wall

with

the

two

screws

provided

(see

Fig.

21).

(d)

Connect

plug from the-.wai-switch wire to

the connector

marked

O/S/C

(J6) on

the control

board.

NOTE:

The descriptions (e),

(f)

and

Fig.22

are

for

Right

Hand

lnstallation.

For Left

Hand lnstallation

break the

tab and

use

the cable

restrainers

the opposite

side.

fl)

Secure

wall

switch wire to

the control

board with

the

cable

restrainer provided.

Break away

the

plastic tab

with a

pair

pliers

to create

an exit point

for the wire

from the

Drive Unit

(see

Fig.

22)

Check

the

exit point of the

wire

from

the

switch base

and

remove

material from the

front

cover of switch,so that

the

cover

does

not cut

through the wire.

Reposition the

two

buttons in the

front

cover

and

refit over

the

switch

base

by pushing on

cover.

Fasten wire

wall

with

suitable fasteners. Make

sure

not

break

through

tle

wire

insulation when fastening. Breaking

the

insulation

will

create

a short

the wire.

Refit

the

light diffuser.

Test

the operation of the switch by pressing

the Open/Close

Button to

move

the

door.

While

the door

siationary

press

the

Light Button to

turn the

light

the

opener On

and

Off.

(e)

(f)

(s)

(h)

(i)

(k)

@*p

FIG.