Automatic Technology Australia Elite Инструкции по установке и руководство пользователя - Страница 15
Просмотреть онлайн или скачать pdf Инструкции по установке и руководство пользователя для Открыватель ворот Automatic Technology Australia Elite. Automatic Technology Australia Elite 20 страниц. Swing gate opener with remote control
Печатать страницуC O D I N G O F R E C E I V E R / T R A N S M I T T E R
SETTING TRANSMITTERS CODES TO
RECEIVER
The Remote Transmitters can be programmed into the gates re-
ceiver to do two functions. Firstly the full Open/Stop/Close, and
secondly the partly open gate for PEDestrian only access. The
memory in the receiver can store up to 111 different remote con-
trol transmitters.
•
Make sure to connect the battery to the Transmitters.
STORING THE TRANSMITTERS CODE
FOR O/S/C
1. Press and hold the Code O/S/C button on the receiver
(Fig 13).
2. Press the button (one of four) on the Transmitter you would
like to use to control the gate for approximately two seconds.
Pause for two seconds. Press the same button again on the
Transmitter for approximately two second (Fig 12).
3. Release the Code O/S/C button (Fig 13).
4. Press the Transmitter button to see if it operates the gate. If
you wish you can code in all four buttons on the Transmitter
so all four can operate the same gate.
STORING THE TRANSMITTERS CODE FOR
PEDESTRIAN ONLY ACCESS
1. Press and hold the Code PED button on the receiver Fig 13.
2. Press the button (one of four) on the Transmitter you would
like to use to control the pedestrian access for approximately
two seconds. Pause for two seconds. Press the same button
again on the Transmitter for approximately two seconds.
3. Release the Code PED button (Fig 13).
4. Press the Transmitter button to see if it operates the gate.
IMPORTANT NOTE The Pedestrian Access Cycle Time Page
13 button [30], must be set to complete setting this feature.
STORING ADDITIONAL TRANSMITTER (S)
FROM A REMOTE LOCATION
Using this method you don't need to have access to the control box
or receiver. However, you do need a transmitter that is pre coded to
the controller's receiver.
IMPORTANT NOTE: The gate must be activated when the
step below is preformed. The moving gate is to confirm from a
remote location that the correct button was pressed and the
transmitter is in range of the opener of a pre coded Transmit-
ter.
1. Take any pre coded Transmitter. Press the button for the
function you require until the gate is activated and release.
2. Then using a small needle press and hold firmly for 2 seconds
through the Coding Hole (Fig 12).
3. Within 10 seconds take the additional transmitter you wish to
code and Press the button (one of four) on the Transmitter you
would like to use to control the gate for approximately two
seconds. Pause for two seconds. Press the same button again
on the Transmitter for approximately two seconds.
DELETING TRANSMITTER CODES
TO DELETE ONE TRANSMITTER
1. Press and hold the Code O/S/C button (pressing the
PED code button will only delete the PED function
for that transmitter) on the receiver [20]
2. Press the button (one of four) on the Transmitter you
would like to delete from the receiver for approxi-
mately two seconds. Pause for two seconds. Press the
same button again on the Transmitter for approxi-
mately two second.
3. Release the Code O/S/C button.
4. Press the Transmitter button to see if it operates the
gate.
TO DELETE ALL TRANSMITTERS
1. Turn off mains power at the switch (and if the battery
backup is connected, remove the VAC shunt [17] and
replace after step 2).
2. Press and hold the Code O/S/C button on the receiver
Fig 13 while turning on the mains power, continue to
hold the Code O/S/C button for a further ten seconds.
3. Press the Transmitter button to see if it operates the
gate. No transmitter should operate the gate.
Page 15
Fig. 12
Fig. 13