Hideaway Soft Close Инструкции по установке
Просмотреть онлайн или скачать pdf Инструкции по установке для Кухонная техника Hideaway Soft Close. Hideaway Soft Close 2 страницы.
Печатать страницуThe Hideaway
Step 1 - Unpack Hideaway Bin
•
Remove all polystyrene.
•
Remove the bucket/s.
•
Please leave the Glad sample pack and instructions inside the bucket for the homeowner.
(NZ only)
Step 2 - Remove the door bracket (fig 2 & 3)
•
Place the mounting panel upside down on a flat surface with the runners facing upwards.
Fully extend the runners
•
. It is critically important that you extend as far as they will open.
•
Undo the nut on either side of the door bracket (these nuts attach the door bracket to
the collar).
•
Remove door bracket - set nuts aside in a safe place (see Fig 2).
•
NOTE: VERY IMPORTANT - do not remove the collar from the runners or the runners from the
mounting panel.
Step 3 - Remove the friction-fitted lid from mounting panel
(fig 4a, 4b & 4c)
•
Mounting panel should still be upside down on a flat surface with the runners facing upwards.
•
To remove the friction-fitted lid - push firmly down on the lid at the back of the unit.
•
Push firmly, distributing pressure to both sides of lid to ensure the lid clears the hooks located on
the left and right hand sides of the mounting panel.
•
Simultaneously, pull the friction-fitted lid forwards until it pulls clear of the mounting panel.
•
Pull the foam pad clear of the mounting panel. Set aside, leaving the plastic cover on.
Step 4 - Top mounting bins only: Install your bins within your
cupboard/carcass
•
Position the mounting panel (now clear of runner inner and collar as well as friction-fitted lid and
foam pad) inside, beneath your carcass / shelf.
•
Position within the centre of the carcass and ensure the front of the mounting panel is sitting
flush with the front of the carcass. Mounting points are located on the top of the mounting panel
for fixing. Secure the mounting panel into place with the 16mm Surefix screws provided.
Any additional mounting points added will null and void warranty.
Step 5 - Install your bin within your cupboard / carcass
•
Your unit has side mounting points as shown in Fig 1. If side mounting, the internal space of the
cabinet must be within the advertised width.
•
The side mounting points are to be secured with the 16mm Surefix screws and washers provided.
Step 6 - Reinstall the friction-fitted lid and foam into mounting panel
•
Rest the foam on top of the friction-fitted lid - the flat side of the friction-fitted lid should be towards
the ground with the folds facing upwards.
•
Slide the friction-fitted lid and foam inside the mounting panel, stopping just before the rear
hooks. (Note: the large fold on the friction-fitted lid sits at the front of the unit, and the rear of the
lid has the slots which reconnect with the hooks located on the mounting panel at the rear).
•
Simultaneously, with one hand, push firmly up on the back of the friction-fitted lid, push the lid above
the hooks and drop into location. Whilst this is happening, with the other hand push the front of
the lid upwards to ensure it rests on the metal support (located at the front of the mounting panel -
fig 4c).
•
The lid should move up and down slightly with ease, indicating correct installation.
Step 6 - Reattach the door bracket
•
Extend the runners once again.
•
Align the door bracket to the collar and lightly tighten in place using the nuts provided.
Soft Close Installation Instructions
®
Fig 1
Top and/or side
mounting points
Friction-
fitted lid
Liner
holder
Mounting
panel
Door
Runners
Buckets
Bracket
Fig 2
Door bracket and collar detached
Door Bracket
Collar
Fig 3
Door bracket and collar attached
Fig 4a
Push firmly on the back of the unit
to ensure the lid clears the hooks
located on the right and left hand
sides of mounting panel