ADEMCO 5804BDV Инструкции по установке - Страница 2
Просмотреть онлайн или скачать pdf Инструкции по установке для Передатчик ADEMCO 5804BDV. ADEMCO 5804BDV 4 страницы. Two way wireless key with voice status
Печатать страницу
To View the House ID
1. Enter House ID mode as described in step 1 (previous
page).
2. Depress the "D" button to view.
3.
The unit will display the stored number as described in
step 4 (previous page). The unit will then exit House ID
mode.
Programming a House ID in the Alarm
Control
N
On VISTA-40, 50P, 100, and above, use Device
Programming mode to enable the RF receiver and enter
the House ID number.
N
On VIA-30PSE, VISTA-20SE, and below, go to field ✶24
and enter the House ID number.
Programming the Buttons
Each 5804BDV is assigned a unique serial number during
manufacture.
Each button on the unit also has a unique
"loop" number that must be programmed into the alarm control
during installation. Assign each button to an individual zone
number and program the Input Type as "BR" (Button Type
RF) by entering "5" in the control's Zone Programming mode.
Then, input the serial number by one of the following
methods:
N
Transmit twice from the device by pressing one of the
buttons when prompted for the serial number.
N
Enter the serial number manually through the keypad.
N
Enter the serial number through V-LINK or Compass
downloader software as applicable.
Be sure to include the loop number of each button during
programming (see loop assignments on previous page).
NOTE: Do not use the 5804BDV for 24-hour silent alarm, as
the unit itself is not silent.
Button C
If you choose not to use the "C" button, you must do the
following to avoid a "Check" condition when the button is
accidentally pressed:
1.
Assign this button to a zone.
2.
After the serial number has been programmed, re-enter
Zone Programming for that zone.
3.
At the "Zone Type" prompt, enter 00 and press [✶].
a) On VIA-30 controls and below, the system will ask
whether you want to permanently delete that zone.
Enter 0 (No). This will cause the system to retain the
serial number, but render the button inactive.
b)
On VISTA-40 and above, continue to press [✶] until
you see the "Enter Zone No?" prompt again. At this
point, Press 00 and [✶]. Then press ✶99 to exit
Program mode.
On VISTA-40 and Above
If a button is assigned to zone type 20 (Arm Stay), 21 (Arm
Away), or 22 (Disarm), you must assign a user to the button in
order for it to operate.
To assign a user number to the Arm/Disarm button:
1. Enter [4-digit User Code] + 8 + [User No.] + [4-digit new
User Code].
2. Answer Yes or No to the "Open/Close Report?" question.
3. Answer Yes to the "RF Button?" question.
4. Enter the zone number assigned to the Arm/Disarm
button. The keypad will show the summary of user
information on its display.
5. Test the Arm/Disarm button to make sure it operates
correctly.
Activating High-Security Mode
In order to activate this device in High-Security
mode you must use a 5881EN receiver.
1.
Program the 5804BDV in Zone Programming mode as
usual.
2.
After programming the unit, exit Zone Programming
mode.
3.
Enter Go/No Go mode at the control panel (see the
control
panel
information.)
4.
Press and hold the "B", "C", and "D" buttons at the same
time until the unit's red and green LEDs flash alternately.
The 5804BDV transmits a special signal to the receiver.
After 2 seconds, the unit will shut down. The unit is now
in High-Security mode.
After activating High-Security mode, Whenever a
button on the unit is pressed, the left yellow LED
flashes to indicate that the unit is in High-Security
mode. If the left yellow LED does not flash when a
button is pressed, repeat steps 3 and 4 above
Deactivating High-Security Mode
Press and hold the "A", "C", and "D" buttons at the same time
until the unit's red and green LEDs flash alternately. After 2
seconds the 5804BDV will shut down and is no longer in
High-Security mode. When the unit is not in High-Security
mode, pressing any button will cause the right yellow LED to
flash.
Adjusting Volume Level
This unit is shipped with the volume set to the lowest level. To
adjust the volume, proceed as follows:
1.
Enter the Volume Level Programming mode by pressing
and holding the "A", "B", and "D" buttons simultaneously
until the unit's red and green LEDs flash alternately.
Note that if no button is pressed for 5 seconds the unit
will automatically shut down and no change to the volume
level is made.
a.
Press the "A" button for low volume level, or
b.
Press the "B" button for medium volume level, or
c.
Press the "C" button for maximum volume level. The
word "Alarm" will be heard at the volume level
selected.
2.
Press the "D" to accept.
Volume level affects the life of the battery. Use low
volume for maximum battery life.
– 2 –
Installation
Instructions
for
specific
.