Dynamis D40 Руководство пользователя - Страница 10

Просмотреть онлайн или скачать pdf Руководство пользователя для Усилитель для музыкальных инструментов Dynamis D40. Dynamis D40 11 страниц.

Печатать страницу

Dynamis

R E V V |

D 4 0

With the main power in the OFF position:

1. Press & hold the Reverb and Store push buttons

together.

2. With the push buttons being held, turn on the

power switch.

3. If the buttons were held correctly, then the CH1,

Ch2, Boost and Bright buttons will illuminate.

4. Release the Reverb and Store buttons once the

CH1, CH2, Boost and Bright Buttons Illuminate.

5. Press the BRIGHT button to toggle the Global

Setting Option.

Now when you proceed to save your favorite settings

on each channel (using the "saving channels and

settings" method in this manual), you can also save

the FX Loop and either of the master volume controls

specifically.

Note: To toggle between the master controls and the

FX Loop on or off, you can use the foot controller.

SAVING A DIGITAL CAB TO A BANK

When you want to save a cab to a bank along with your

favorite channels and settings to be recalled when you

press the bank button, the save must be performed in

the following order:

1. Select the bank you plan to make the save to.

2. Select the channel as well as boost modes you plan

to save to the bank. At this point the bank LED on

the foot controller will begin to flash.

3. Next you will need to select the cab you want saved

to the bank. Note: If channel functions (Bright) are

selected first, the cab will not be saved. Boost is not

included as a function in this case.

4. Once you have selected your cab, you may proceed to

then select the functions you plan to save to the bank

(Bright).

5. Once completed, press the bank button to store

these settings, the bank LED will stop flashing

confirming the save.

SAVING A DIGITAL CAB TO A CHANNEL

One cool feature of your amplifier is the ability to save

digital cabs to each channel. This will allow you to have

many different sounds with every channel. In order to

save a cab to a channel:

In order to save a cab to a channel:

1. Select the channel and boost (If applicable, as

boost is considered a channel) you want to save a

digital speaker cab to.

2. Select the digital speaker cab bank you would

like saved with the 6 position rotary switch or two

notes remote software.

3. Press and hold the store button until the LED

flashes.

Now every time you switch to that channel, the digital

speaker cab you have saved will be loaded by the Two

Notes technology inside!

DISABLE/ENABLE CAB SPEAKER

For those that have no desire to save digital speaker

cabinets, this feature can be disabled so that only

the same cab will be used no matter what channel or

setting you change.

With the main power in the OFF position.

1. Press & hold the Reverb and Store push buttons

together.

2. With the push buttons being held, turn on the

power switch.

3. If the buttons were held correctly, then the CH1,

Ch2, Boost and Bright buttons will illuminate.

4. Release the Reverb and Store buttons once the

CH1, CH2, Boost and Bright Buttons Illuminate.

5. Press the CH1 button to toggle the Option.

FACTORY RESET

If you would like to clear the amp's memory of all saved

program patches & restore all of the amps settings

to the factory default, which includes MIDI channel

(restored to CH1), OMNI Mode, FX Loop (Restored to

off at power-up) & a full memory clear, proceed with the

procedure below:

With power OFF, press & hold the CH1 button & the

CH2 button together & turn the power switch to the ON

position.

The amplifier will flash the Reverb LED to confirm that

the factory defaults have been restored..

Note: When resorting to the factory reset, just remember

that ALL settings in the amps memory will be erased.

R E V V |

Dynamis

D 4 0