DBI SALA ROLLGLISS R550 Руководство пользователя - Страница 9

Просмотреть онлайн или скачать pdf Руководство пользователя для Датчики безопасности DBI SALA ROLLGLISS R550. DBI SALA ROLLGLISS R550 16 страниц. Rescue & escape device

DBI SALA ROLLGLISS R550 Руководство пользователя
6.0 MAINTeNANce, seRvIce, sTORAGe
6.1

MAINTENANCE:

• Rollgliss R550 Descender: Periodically clean the exterior of the R550 Rescue & Escape Device with
water and mild detergent. Position the device so excess water will drain out. Clean labels as required.
Clean lifeline with water and mild detergent. Rinse and thoroughly air dry. Do not force dry with heat. A
buildup of dirt, paint, etc., may prevent the lifeline from pulling through the device. Ensure no knots are
present.
• Humidity Resistant Case: If inspection of the Humidity Indicator indicates the Humidity Resistant Case
has experienced high humidity (see Section 5.3), perform the following maintenance:
◊ Replace the Pie Sector Indicator Disc (see Figure 11):
1. Grasp the Humidity Indicator housing by the Hex Flange on the outside of the case.
2. Insert a 1/2" hex wrench (Allen Wrench) into the Externally Threaded Collar and turn the
Collar counter-clockwise to loosen.
3. Remove the Externally Threaded Collar.
4. Remove the Teflon Washer.
5. Remove the old Pie Sector Indicator Disc.
6. Install a new Pie Sector Indicator Disc (P/N 9505223).
7. Install the Teflon Washer.
8. Install the Externally Threaded Collar.
9. Hold the Humidity Indicator housing by the Hex Flange and Torque the Externally Threaded
Collar to 45-55 inch-lbs (5-6 Nm ).
◊ Just prior to resealing the Humidity Resistant Case, replace all Moisture Absorber Packets in the case
with new packets (P/N 9505148). Each new Moisture Absorber Packet is wrapped in a foil bag. Remove
the foil bag before placing the the new packet in the case.
6.2
sERvICE: Maintenance and service must be completed by an authorized service center. An authorization
and return number must be issued by Capital Safety. Do not attempt to disassemble the device. The R550
Rescue and Escape Device requires service by an authorized service center every five years (when properly
stored and maintained) with the exception of units used in training applications, which require service every
two years. Service by an authorized service center is also required when the Maximum Cumulative Descent
Distance has been reached or when the product fails an inspection. Descent Distances should be logged and
totaled in the Descent Log (Section 10). Service by an authorized service center shall include an intensive
inspection and cleaning of all components and replacement of Friction Pads as required. Failure to provide
required service may shorten the product life and compromise safety and performance.
NOTe:
Only Capital Safety or parties authorized in writing may make repairs to this equipment.
6.3
sToRAGE: Store the R550 Rescue & Escape Device in a cool, dry, clean environment, out of direct sunlight.
Avoid areas where chemical or organic vapors are present. Thoroughly inspect the R550 Descender after
extended storage. If the R550 Rescue and Escape Device can not be stored in a proper environment, a
humidity resistant case should be used.
NOTe:
Descender devices installed at a workstation and left in place between inspections should be adquately
protected from environmental conditions.
Figure 11 - Humidity Indicator Disc Replacement
Externally
Allen
Threaded
Wrench
Collar
Teflon
Washer
Humidity
Indicator
Hex
Disk
Flange
9
Pie Sector
Indicator Disk
Externally
Threaded
Collar