Galaxy DX 98VHP Руководство пользователя - Страница 2
Просмотреть онлайн или скачать pdf Руководство пользователя для Трансивер Galaxy DX 98VHP. Galaxy DX 98VHP 11 страниц. 10 meter amateur mobile transceiver with built-in frequency counter & starlite face plate
Печатать страницу
CHAPTER 1 SPECIFICATIONS
GENERAL
Model
Frequency Range
Emission
Frequency Control
Frequency Stability
Temperature Range
Antenna Impedance
Antenna Connectors
Input Voltage
Size
Weight
TRANSMITTER
RF Power Output
Current Drain
Spurious Emission
Unwanted Sideband
Audio Distortion
Frequency Response
Microphone
Clarifier Range
RECEIVER
Sensitivity for 10 dB (S+N)/N
Squelch Sensitivity
Selectivity
Image Rejection
AGC Figure of Merit
Audio Power Output
Audio Response
(SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE)
DX 98VHP
28.315 ~ 28.755 MHz
AM/USB/LSB
Phase-Lock-Loop (PLL) Synthesizer
0.001%
-30 C to +50 C
50 Ohms
Standard SO-239 type
13.8V DC
7 7/8" (W) x 3 1/8" (H) x 10 3/4" (D)
10 lbs.
AM: 10W~50W
USB/LSB: 200W PEP
AM: 25 Amps
SSB: 40 Amps
-50 dB
-50 dB
10%
300 to 2500Hz
Dynamic
Coarse: ± 6.0KHz, Fine: ± 1.0KHz
AM: < 0.5 ìV; USB/LSB: < 0.25 ìV
< 0.5 uV
-55 dB
-50 dB
100 mV for 10dB Change in Audio Output
2.5W @ 10% Distortion
300 to 2500 Hz
2
CHAPTER 2 INSTALLATION
INSTALLING THE RADIO
Choose a convenient location for operation that does not interfere with driver or
passenger. This radio is supplied with a universal mounting bracket. When mounting
the bracket and radio to your car, make sure it is mechanically strong. Also, provide a
good electrical grounding connection to the chassis of vehicle. Proceed as follows to
install the radio.
1. Locate a convenient area in your vehicle for the installation of the radio. Hold the
mounting bracket with the radio in the location where the radio is to be installed.
Make sure nothing will interfere with either the radio or the mounting bolts. Mark
and then drill holes for the mounting bracket.
2.
Most radio antennas come equipped with a PL-259 plug. Connect this plug to the
ANT. Jack in the rear of the radio.
3.
Extending from the rear of the radio is a fused red and black wire for the DC
connections to the vehicle's electrical system. For best performance, it is strongly
recommended that the Red lead be connected directly to the positive terminal on
the vehicle's battery and the black lead be connected directly to the negative
terminal on the battery. (Note, not connecting both leads direct to the battery may
cause performance problems) This radio is designed for vehicles with negative
ground systems.)
Connections should be made using appropriate "crimp on" lugs of a size large
enough to make good contact with the bolt used to fasten to the. It is a good safety
idea to install a second 50 amp fuse that would provide protection in case the red
wire was to "fray" or get pinched and short to the body of the vehicle, somewhere
between the battery and the radio.
High power radios such as this one require large DC current flow when in the TX
mode. Poor power connections cause supply voltage drops that can substantially
decrease the performance of your radio. A good DC connection is probably one of
the most important things for getting the best transmitter performance and in some
cases, least receiver noise.
4.
Mount the microphone bracket near the radio in an easily accessible spot using the
two screws provided.
3