Autopage DS-434 Краткое руководство по установке

Просмотреть онлайн или скачать pdf Краткое руководство по установке для Дистанционное пусковое устройство Autopage DS-434. Autopage DS-434 2 страницы.

Печатать страницу

QUICK START INSTALLATION GUIDE

Help Auto Page protect our environment !

If you are not proficient in the installation of this product or would

like a full version of the installation manual, Please visit our web

site @

www.autopageusa.com

FOR PROFESSIONAL INSTALLATION ONLY!

7-PIN MAIN WIRE HARNESS

PROGRAMMING TRANSMITTER

Note: This model will only retain the last 4 remote transmitters programmed. If the

transmitter memory is exceeded, the security system will start deleting transmitters from

memory in chronological order.

Turn the Ignition 'switch „OFF/ON‟ 3 TIMES and stay in the ON position.

"Within 15 seconds".

Push the Valet switch 2 times and hold it on the 2nd push until LED flashes and

long chirp is heard then release the valet switch. You are now in the Transmitter

programming mode.

Press and hold any button of the transmitter until the siren responds with a

confirming chirp indicating the signal has been stored into memory.

If you have additional transmitters (up to 4) that need to be programmed,

repeat step 3 for each transmitter.

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light

flashes will confirm exit.

FEATURE PROGRAMMING

NOTE: An XT-33 transmitter must be programmed to

the unit in order to program the unit features!

A Programming

Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

Push the Valet switch 3 times (holding in on the 3

push) until LED Flashes &

one chirp with one long chirp is heard, then release the valet switch. You are

now in the Alarm feature "A" programming mode.

Press and release the transmitter button corresponding to the feature you want

to program.

The siren chirps and LED pause will indicate previously setting.

The factory default settings is always [1] LED flash, [1] chirp.

4. Depress the transmitter button to change the feature. Simply keep re-depressing the

transmitter button until the system advances to your desired setting.

One Chirp /

Press

LED one

Three

Four

Two Chirps /

Transmitt

pulse

Chirps /

LED two

Factory

LED three

LED four

pulses

Default

Button

pulses

Setting

Factory

Without this

alarm disarm

feature

with CH 3 ON

Parking

light turns

"on" for

30-

Parking light

second

Pathway

turns "on" for

upon an

Illumination

30- second

unlock

Feature "off"

upon an

signal &

unlock signal

10-second

upon a

lock

signal.

DBI Unlock

DBI Two step

ALL doors

unlock

Ground

AUX 2 =

out when

Aux 2 = CH4

Trunk

running

Ground

Horn output

Aux 1 = CH4

out when

running

Lock/Arm &

Unlock/Disar

Lock/Arm

All chirps

Confirmation

OFF

Confirmation

Only

Chirp

Without

Ignition

ignition

controlled

door

door locks &

locks

unlocks

only

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light

flashes will confirm exit.

DS-434

B programming

Turn the Ignition switch „ON/OFF‟ 3 TIMES and stay in OFF position.

Push the Valet switch 5 times (holding in on the 5

two chirps with one long chirp is heard then release the valet switch. You are

now in the Alarm feature "B" programming mode.

Press and release the transmitter button corresponding to the feature you want

to program.

One Chirp /

Press

Two Chirps /

Three Chirps /

LED one pulse

Transmitter

LED two

LED three

Factory Default

Button

pulses

Setting

Flashing

Constant

parking light

output upon

Remote Start

Press

button twice =

button once =

Activate Remote

Activate

Start.

Remote Start.

20 minutes run

30 minutes

10 minutes run

time

run time

time

Door lock

before start

Door lock before

after shut-

and Door lock

start

down

after shut-

down

Channel 3

Output =

Pulsed output

Latched

Latched output

(XT74 Upgrade Kit

output

and reset with

must be used to

ignition "on"

access this

feature)

CH 4 output =

CH 4 output

Five

Momentary

CH 4 output

= Latched

Chirps

output

(XT74

= Latched

output and

and five

Upgrade Kit must

output

reset with

LED

be used to access

ignition ON

this feature)

blinks

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking

light flashes will confirm exit.

C Programming

Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

2 Push the Valet switch 7 times (holding in on the 7th push) until LED flashes & three

chirps with one long chirp is heard then release the valet switch. You are now in the

Alarm feature "C" programming mode.

3 Press and release the transmitter button corresponding to the feature you want to

program.

One Chirp /

LED one

Three Chirps

Press

Two Chirps /

pulse

Transmitter

LED two

Factory

Button

pulse

Default

Setting

Exit the programming mode. (3 long chirp & 3 parking light

flashes to confirm this exit.)

A> RPM learning – see RPM Learning page 26.

Ground

0.8-second (2 chirps), 1.0-second (3 chirps),

out when

B> Start

1.2-second (4 chirps), 1.4-second (5 chirps),

start

Crank Time:

1.6-second (6 chirps), 1.8-second (7 chirps),

0.6-second

2.0-second (8 chirps), 3.0-second (9 chirps),

Ground

4.0-second (10 chirps),

out when

start

Low check

Hi check level

level

Start or Stop the system for TESTING & ADJUSTMENT

Data Bus

Timer

Interface

checking

Mode**

+ 50 RPM

No RPM

DBI ONLY

learning

No RPM

- 50 RPM

Learning or <

DBI ONLY

50RPM

push) until LED flashes &

FEATURE "C" MUST BE PROGRAMMED FOR THE

UNIT TO RESPOND TO REMOTE START!

If you are not sure or do not understand any part of

the quick start guide, please download the complete

Four Chirps /

LED four pulses

installation

manual

www.autopageusa.com

This quick start guide is a

brief outline for professional installers that are

familiar with the installation and operation of this

remote start system.

Please test all of your

installation to insure proper operation of the vehicle

before returning it to the customer.

For authorized dealer technical support, please call

800-945-2527

and

wait

technician.

Technical support hours are Monday

through Saturday from 8:00 to 5:00 Pacific standard

5 minutes run time

time.

This Remote Starter with Keyless Entry System has been

Without this feature

designed to be installed on fuel-injected vehicles with an

automatic transmission ONLY.

Never install

this remote starter

Channel 3 Output =

transmission vehicle.

Timer programming (set

to any interval between

This system must be installed and wired through a

1 second and 2

safety switch so it will not start in any forward or reverse

minutes.)

gear.

Some automatic transmission vehicles mainly older GM

vehicles with a purple starter wire have a mechanical-type

CH 4 output = Timer

park safety switch instead of electrical safety switch. The

programming (set to

mechanical type does not interrupt the starter circuit when

any interval between

the transmission is in any gear and does not offer the 100%

1 sec. to 120 sec.)

level of safety required for remote starting purposes.

Therefore, our system should never be installed on any

vehicle that uses a mechanical type park safety switch.

Once you install this system, you must verify that the

vehicle will not start in any forward or reverse gear,

regardless of the type of vehicle.

Read the operation manual for operating.

Do not install any component near the brake, gas pedal

or steering linkage.

Some vehicles have a factory installed transponder

immobilizer system that can severely complicate the

Four Chirps /

installation. There is a possibility that this system cannot be

LED four

LED three

installed on some immobilizer-equipped vehicles.

pulse

Most vehicles have an SRS air bag system. Use

extreme care and do not probe any wires of the SRS

system.

Disconnect the car battery before beginning work on the

vehicle.

Check behind panels before drilling any holes. Ensure

that no wiring harness or other components are located

behind the panels that would otherwise be damaged.

Do not use conventional crimp lock, bullet on any wiring.

Poor wiring, i.e. taped joints will possibly introduce

unreliability into the alarm system and may result in false

alarms or incorrect operation. We suggest soldering all

connection points.

Install the wiring neatly under carpets or behind trim to

prevent possible damage to wires.

960 Knox Street Unit B

Torrance, California 90502

Main Office: 310-323-1800

Technical Support: 800-945-2527

(For Authorized Dealers Only)

www.autopageusa.com

available

for

the

first

available

manual