AUTOSCALER AW30C Руководство - Страница 4

Просмотреть онлайн или скачать pdf Руководство для Медиаконвертер AUTOSCALER AW30C. AUTOSCALER AW30C 14 страниц.

Печатать страницу



Water Control Knob: For adjusting the flow of water to the

handpiece and insert tip. To obtain the necessary water flow of at

least (18cc - 30cc/+/minute) turn the WATER KNOB clockwise.

HIGHER water flow to the RIGHT, and LOWER water flow to the

LEFT.



Handpiece Panel Receptacle: Accepts the male side of the

Handpiece connector with lock ring.

HANDPIECE ASSEMBLY

The handpiece assembly is used to accept Cavitron® interchangeable

insert tips. It is connected to the AUTOSCALER® front panel by a Quick

Connector. The open end of the handpiece will accept all Cavitron®

brand: "P", "TFI™", "SLIMLINE™" or "FSI™" style 25,000Hz (25K)

inserts. If you ordered a 30,000Hz (30K) model AUTOSCALER®, you

must use the shorter (30K) frequency insert tips.



30K tips measure (Shorter style approx. 6.25 inches long)



25K tips measure (Longer style approx. 7.25 inches long)

(25K) inserts will NOT work in your 30K unit.

(30K) inserts will NOT work in your 25K unit.

Inserts are extremely FRAGILE. If one is dropped, bent, or scratched it

WILL NOT cavitate (i.e. will not function) or function by operating at a

higher than normal temperature, and should be replaced immediately.

Insert tips should be routinely replaced according to insert

manufacturer's recommendations.

ELECTRICAL REQUIREMENTS

A GROUNDED wall receptacle is required supplying a voltage range

of 110-125 volts 50/60 Hz A.C. If a 3 to 2 prong adapter is used, the

ground wire MUST be connected to the base plate screw. Have an

electrician test your outlet for correct wiring polarity and a safe

ground. Do not assume the ground is complete. If you plug the

AUTOSCALER® in a GFI (Ground Fault Interrupt ) outlet it may trip the

socket due to the high sensitivity of the socket. If this occurs plug the

AUTOSCALER® into a non-GFI socket.

*Cavitron®, SLIMLINE™, FSI™, and TFI™ are registered trade marks of Dentsply Sirona

INSTALLING THE HANDPIECE ASSEMBLY

1. Align the electrical contacts of the MALE connector with the same on

the FEMALE panel connector.

2. Gently insert the connector. It should slide in with very little effort. If

the connector does not align, DO NOT force it. Turn the CONNECTOR

BODY in either direction until the connector correctly aligns and goes

in.

3. Once the connector has been completely inserted, screw the OUTSIDE

LOCK RING to the RIGHT with light finger pressure until it stops. DO

NOT over tighten the lock ring, be careful not to cross thread the lock

ring.

4. To remove the connector, unscrew the lock ring to the left, and gently

pull outward grasping the entire connector body.

INSTALLATION AND OPERATION

DO NOT use your AUTOSCALER® until all of the following steps have been

completed.

1. Upon receipt of your unit carefully unpack it and see that the Toggle

Switch is in the OFF-O position.

2. The Water Control Knob should be in the HIGH position by turning

the water control knob all the way to the RIGHT.

3. Set the Power Knob all the way to the LEFT in the LOW position.

4. Plug the male Water Quick Release Valve water connector into the

Dental operatory or have a plumber install a SHUT OFF style FEMALE

connector. A minimum of (20 P.S.I.) water input pressure and a

maximum of (60 P.S.I.) is needed from the operatory for proper oper-

ation of the AUTOSCALER®. It is recommended that water line filtra-

tion be used to remove larger particles before entering the scaler.

5. Plug the power cord into the wall (see electrical requirements). Press

the toggle switch to the ON-I position. The L.E.D. light above the

switch should be ON ("I" position).

6. Select an insert. Moisten the rubber O-RING before inserting into

the handpiece. While holding the handpiece UPRIGHT place the

insert in the open end of the handpiece and with a gentle PRESS and

TURN motion, snap the insert in fully. DO NOT force the insert.

7. Manufacturer recommends the use of a disposable handpiece

sleeve/barrier be used over the handpiece assembly. Place the

sleeve/barrier over the handpiece. While holding the sleeve/

barrier in place, puncture the insert through the plastic at the open

end of the handpiece, and snap the insert in fully. Dispose of

sleeve/barrier after each patient.

8. Due to atmospheric exposure and exposure to sterilization solutions

the O-RING on the insert tip may become swollen, brittle, or crack,

and require replacement.