Highlander iP-1 Руководство - Страница 4

Просмотреть онлайн или скачать pdf Руководство для Аксессуары для музыкальных инструментов Highlander iP-1. Highlander iP-1 4 страницы. Integrated pickup and preamplifier for acoustic guitar and bass integrated pickup and preamplifier for acoustic guitar and bass

Печатать страницу

Installing the Pickup

The consistent string balance achieved with this 'two hole' installation technique is due to the mechanical symmetry of having the same type of bend at

each end the pickup. This causes the mechanical forces such as sound vibrations that are acting on the pickup to be well balanced throughout the pickup.

Check the 'Saddle Fit': This is important information for the correct operation of all under saddle pickups.

The saddle should move freely

up and down in the saddle slot.

To help maintain the 'Saddle Fit' during variations in humidity and

temperature, lightly wax the bridge and the inside of the saddle slot. Be

sure to remove any excess wax from the slot and especially the groove.

Polishing the sides of the saddle helps create a smooth, sliding fit.

Install the Pickup in the Groove

Pickup

Trim and Install the Saddle

Measure the difference in saddle height using either

the line scribed or the height measured in step

Press the saddle down firmly on to the pickup and replace the strings. Start with the 'D' String. While tensioning it, press the

5c 5c

Restringing

saddle back (away from the sound hole) and down to prevent the saddle from binding in the saddle slot.

Next, replace the 'G' String then the rest of the strings. Plug in and check the string balance and sound quality of the installation.

If the tip or the crimp comes into contact with

the brace they could vibrate and create an

unwanted sound. A soft pad between them and

the brace (like a piece of double stick foam on

the brace) can prevent any potential problems.

The pickup will not function correctly if the tip is placed under the saddle, the tip must be inserted in the hole as illustrated above.

Removing the tip of the pickup or the use of solvents, super glue or lacquer on the pickup will compromise its operation and will void the warranty.

The information and graphics contained in this document are the property of Highlander Musical Audio Products. Copying of any kind is prohibited, except for personal use only.

Consistent String Balance is achieved with this 'Two Hole' installation.

Too loose and the saddle can

Too loose

bind under string tension.

Note: These types of 'Saddle Fits' may sound o.k. acoustically, however, the

saddle needs to be in full contact with the pickup for a good amplified sound

and to insure the best acoustic tone and sustain.

Pass the pickup up through the hole at the 'Low E' side of the bridge and then down through

the hole at the 'High E' side of the bridge.

'Low E' side

Maintain a small

gap between the

crimp and the top

of the guitar.

Trim the difference from the

underside of the saddle.

The underside of the saddle

must be really flat.

Check with a straight edge.

Saddle

Saddle Material: Micarta

helps with string balance. Bone can be inconsistent, when

choosing a piece hold it to a light and look for even color.

The tip is a special electrically shielded

termination that helps to prevent hum and

interference even when the pickup is used

with an amplifier that is not grounded.

Tip

It also makes the pickup easier to handle.

Using the saddle or a piece of wood, apply just

enough pressure to seat the pickup in the groove.

Check the saddle height.

has a consistent density which

Crimp

Too tight and the saddle

Too tight

may not be fully seated.

Pickup

Once the original saddle

height is achieved,

chamfer and debur the

bottom edges of saddle

to help prevent binding.

We recommend that

strings be replaced

two at a time from

now on, it will help

maintain the stability

of the installation.

Highlander Musical Audio Products 1991-2009