Dynatuner FM-1 Инструкции по сборке Операция выравнивания - Страница 9

Просмотреть онлайн или скачать pdf Инструкции по сборке Операция выравнивания для Тюнер Dynatuner FM-1. Dynatuner FM-1 20 страниц.

Печатать страницу
3~Wist
together the two red and the red-yellow power
transformer wires. Connect one red wire to pin #1
of socket V9 (8). Connect the other red wire to pin
#7 of socket V9 (8). Dress the red-yellow wire over
to the twisted mounting tab on the quadruple section
electrolytic capacitor, and connect this wire as
shown in the pictorial.
4 (
~onnect
one end of a 2)/2" black wire to lug #2 of
the three lug terminal strip. Connect the other end
to the ground lug of the quadruple section electro-
lytic capacitor used in the previous step. 80lder
both wires.
5 (/Connect the green-white transformer wire to lug #2
of the three lug term.inal strip. Note that the wire is
inserted into the lower hole of the lug
(8)~
6(
~Connect
the green transformer wire to lug #1 of the
three lug terminal strip. This wire is inserted into
}he lower hole of the lug (8).
7 (
-y(
Twist together the two black transformer wires.
Connect one wire to lug
1/2
of the AC outlet. Connect
the other wire to lug #2 of the fuse holder (8).
8( YConnect one end of a 1)/2" green wire to lug
Ifl
of
the three lug terminal strip. Connect the other end
to pin
H4
of socket V9 (8).
9( It"'Connect one end of a 1)/z" black wire to lug
#2
of the
three lug terminal strip. Connect the other end to
pin #5 of socket V9 (8).
10(
VI
Connect one end of a 500 ohm 5 watt resistor to
lug #1 of the quadruple section electrolytic capacitor.
Connect the other end to lug #2 of the capacitor.
11 ( /
Connect one end of a 2" red wire to pin #3 of socket
V9 (8). Connect the other end to lug #1 Of the
quadruple section electrolytic capacitor
(8-).
12(
j
Connect one end of the other 500 ohm 5 watt' resistor
to lug #2 of the quadruple section electrolytic capaci-
tor (8).
Connect the other end to lug #3 of the
capacitor.
13(vf Connect one end of a 470 ohm
(yell~,
violet, brown)
one watt resistor to lug #3 of
th~
quadruple section
electrolytic capacitor. Connect the other end to lug
{l4
of the capacitor.
The following steps will refer to eyelet,> on the
etched circuit boards. Always be certain that you
are connecting to the correct point. The electrical
requirements of the layout of the circuit board,
combined with the tight space allowance, may lead
.to confusion unless the relationship of numerals and
eyelets is carefully observed. Refer to the diagrams
of the boards.
14(
IJ
Connect one end of a 6" green wire to lug #1 of the
three lug terminal strip. Feed this wire through
grommet #1, and connect the other end to eyelet #18
on PC-8 (8). Remember that when soldering to an
eyelet, a srpooth well-soldered joint must be made
from the wire to the eyelet to the copper.
15(
-vIf
Connect one end of a 2~" green wire to eyelet #17
on PC-8 (8). Connect the other end to eyelet #14 (8).
16(
J)
Connect one end of a 3)/2" green wire to eyelet #1
on PC- 7 (8). Connect the other end to eyelet #5 (8).
17 (
~Connect
one end of a
7"
green wire to eyelet 116 on
PC-7 (8). Connect the other end to eyelet #13 of
PC-8 (8).
1 M Connect one end of a
4"
green wire to eyelet #19 on
PC-8 (8). Connect the other end to eyelet 1124 (8).
19("") Connect one end of a 4%," red wire to lug
ff.3
of the
quadruple section electrolytic capacitor. Feed the
wire through grommet #1 and connect the other end
to eyelet #22 on PC-8 (8).
20(
0'
Connect one end of a 7)/z" green wire to eyelet #20
on PC-8 (8). Feed the wire through grommet
Ifl
and
connect the other end to lug
111
of the three lug
terminal strip.
21 (..{ Connect one end of a
6~"
green wire to eyelet #35
on PC·8
(8).
Feed the wire through grommet #2 and
connect the other end to lug
.n
of the three lug
terminal strip.
22(.15
Connect one end of a 5" red wire to eyelet #21 on
PC-8
(8).
Connect the other end to eyelet #16
(8).
23(
'If
Connect one end of a 9" red wire to eyelet
H15
on
PC-8 (8). Connect the other end to eyelet #9 on
PC-7 (8).
24
(.1
Connect one end of a 7" red wire to lug #3 of the
quadruple section electrolytic capacitor. 80lder all
four wires. Feed the wire through grommet
HI
and
connect the other end to eyelet
1127
on PC-8 (8).
25(,-1 Connect one end of a 9)/z" red wire to lug 114 of the
quadruple section electrolytic capacitor. Feed the
wire through grommet #2 and connect the other eud
to eyelet #34 on PC-8 (8).
26(
v(
Twist together a 10" black wire and a 6!/z" black
wire, keeping one pair of ends even. Connect one of
the even ends to lug #1 of the on-off switch. Connect
the adjacent end of the other wire to lug
112
of the
on-off switch. Feed the pair through grommet
112.
Connect the other end of the longer wire to lug #2
of the AC outlet (8). Connect the other end of the
shorter wire to lug #3 of the three lug terminal strip.
27(/) Connect one lead of the .02 mfd capacitor to lug #1
of 'the on-off switch (8). Connect the other lead of
the capacitor to lug #2 of the switch (8). Place the
body of the capacitor under the switch where it is
away from the etched circuit board. Refer to the
pictorial.
28(
j
Connect one end of a 2" black wire to iug #1 of the
AC outlet. Oonnect the other end to lug #1 of the
fuse holder (8).
29( ) Connect one end of a 9J,i" green wire to eyelet
!~39
on PC-8 (8). Connect the other end to the center
lug of output socket A.
30(/)' Connect one e;d of a 1)/2" green wire to output
socket A center lug (8). Connect the other end to
the center lug of output socket B (8). Refer to the
Appendix
if
one of these sockets is to be connected
for use with an external multiplex adapter.
.31
(fJ
Connect one end of a 5" red wire to lug
114
of the
quadruple section electrolytic capacitor. 80lder all
three wires. Connect the other end to eyelet /1-12 of
PC-7 (8).
7