Galvin Engineering Safe-Cell 50150 Установка изделия Manualline - Страница 4
Просмотреть онлайн или скачать pdf Установка изделия Manualline для Сантехническая продукция Galvin Engineering Safe-Cell 50150. Galvin Engineering Safe-Cell 50150 4 страницы. Prison basin set
Печатать страницу
TROUBLESHOOTING
PROBLEM
CAUSE
Blocked flow restrictor
Inconsistent
flow
Dirt in the top assembly cartridge
Continuous
Top assembly cartridge loose or
flow
internally obstructed or damaged.
Supply not on
Water is not
flowing from
Blocked flow restrictor
tap
The flow restrictor may not be
Rate of flow
satisfactory due to inadequate supply
inadequate
pressure
Button hard
The mains pressure may be too great
to press
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer's warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer's warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer's warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.
In the absence of a legal or industry definition of anti-ligature or ligature resistant products, when we use these terms, we are referring to
products that are designed and manufactured with the intention of reducing the risk of ligature attachment to the product(s).
Galvin Engineering Pty Ltd will always endeavour to design and test our anti-ligature product(s) to reduce the risk of product ligature attachment that may result in
serious injury or death.
Whilst all reasonable measures are taken at the time of design, the anti-ligature design of the products are not intended to and will not:
a. Replace protective measures that need to be taken in the specific circumstances of usage;
b. Substitute the need for supervision of those who may be at risk;
c. Protect and or prevent those at risk against any self-harm instances that may occur when installed; and
d. Protect and or prevent injury when the risks where unknown to us at the time of the design of the product(s).
Galvin Engineering Pty Ltd does not offer and does not represent or warrant that any product(s) for sale that are ligature-free.
Therefore, Galvin Engineering will not be liable for any claims, loss, or damages arising from ligature attachment on our products. It is the purchaser's responsibility
to ensure that products purchased and installed are suitable for the environments in which they are installed, and suitable supervision and protective measures are
in place to protect those at risk.
Version 1, 30 August 2018, 4 of 4
RECTIFICATION
Remove isolation valve, remove flow restrictor & clean
with water
Remove cartridge, clean with water and re-grease
spindle if required.
Remove cartridge, clean with water and re-grease
spindle if required.
Turn water on
Remove flow regulator from tap and remove debris.
Install an inline strainer to stop further blockages.
Remove flow restrictor and replace with a flow restrictor
of different capacity to suit (available from Galvin
Engineering)
Reduce to below 500kPa (70PSI), re-grease spindle if
required
Version 1, 30 August 2018, 4 of 4