HIKOKI G 10VE2 Инструкция по обращению с предметами - Страница 10

Просмотреть онлайн или скачать pdf Инструкция по обращению с предметами для Шлифовальный станок HIKOKI G 10VE2. HIKOKI G 10VE2 20 страниц.

Печатать страницу

English

SPECIFICATIONS

Model

Voltage (by areas)*

Power Input*

2800–10000 /min 2500–8500 /min

Rated speed

Outer dia.

Wheel

Hole Dia.

Thickness

Peripheral speed

Weight

(Only main body)

*1 Be sure to check the nameplate on product as it is

subject to change by areas.

Electronic control

○ Soft start

Reduces recoil against the operator by managing the

number of rotations during startup.

○ 0 Voltage Re-start Protection

The 0 voltage restart protection feature prevents the

power tool from restarting after the power has been

temporarily cut oﬀ during operation.

○ Constant speed

○ Overload protection

This protection feature cuts oﬀ the power to the motor

in the event of overloading of motor or a conspicuous

reduction in rotational speed during operation.

When the overload protection feature has been

activated, the motor may stop.

In this case, release the tool switch and eliminate causes

of overloading.

After that you can use it again.

○ Rotation recovery control function

When the motor is stopped due to overloading, if the

cause is eliminated, the motor automatically resumes

operation.

During grinding, if the motor stops due to pressing too

forcefully with the grinder, gently lift the tool body to start

rotation again.

When the motor is stopped for a certain period of time,

it does not recover, for the protection of the unit and for

safety.

Turn it oﬀ once and on again to start it.

○ Overheat protection

This protection feature cuts oﬀ the power to the motor

and stops the power tool in the event of overheating of

motor during operation.

When the overheat protection feature has been

activated, the motor may stop.

In this case, release the tool switch and cool it down in a

few minutes.

After that you can use it again.

NOTE

Due to HiKOKI's continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

G10VE2

G13VE2

(110 V, 220 V, 230 V, 240 V)

110 V: 1050 W

220 V: 1200 W

230–240 V: 1320 W

100 mm

125 mm

16 mm

22.23 mm

6 mm

72 m/s

80 m/s

1.5 kg

1.7 kg

MOUNTING AND OPERATION

Action

Fitting and adjusting the wheel

guard

Fixing the side handle

Assembling depressed center

wheel

Assembling cutting wheel

Assembling diamond wheel

Switch operation

Grinding angle and grinding

method

Adjusting the number of revolution

Mounting and dismounting the

ﬁ lter set

Selecting accessories

*1 Sold separately

*2 WARNING

Before use, be sure to tighten the wheel nut with the

included wrench.

Failure to tighten could result in the wheel nut

loosening when the brake is activated during a stop.

NOTE

The wheel washer is speciﬁ cally for this product. Do

not use it for any other product.

*3 When the 0 voltage re-start protection feature has been

activated, return the power switch to the OFF position

and wait for 1 second or more before restarting the

power tool.

*4 Adjusting the number of revolution

This model is equipped with an electronic inﬁ nite-

variable-speed drive and can change the number of

revolution according to a use.

If you turn and set the dial scale (Fig. 9) to 6, the number

of revolution increases, and if you turn and set it to 1, the

number of revolution decreases.

Before use, set the number of revolution using the dial. In

so doing, refer to the following table as a rough guide.

Dial

Use

Polishing, ﬁ nishing

Removal of paint

or coat

Removal of rust

Removal of burrs

Grinding

Rough grinding

Cutting

NOTE

○ Use caution not to turn the dial scale to any value below

1 or above 6.

*5 NOTE

○ When detaching the ﬁ lter, be careful not to let debris

enter the tool body.

○ Keep the ﬁ lter set attached except during cleaning or

replacement.

Figure

―

Tools

Radial grinding disc

Sanding disc

Depressed center wheel

Diamond wheel

Page