HIKOKI WR18DH Инструкция по обращению с предметами - Страница 13
Просмотреть онлайн или скачать pdf Инструкция по обращению с предметами для Ударный драйвер HIKOKI WR18DH. HIKOKI WR18DH 20 страниц.
Печатать страницуMOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
How to use the hook*
1
Mounting the socket*
2
Reversing the rotational direction*
Switch operation
How to use the LED light*
Tightening mode selector function*
Auto stop mode*
6
Auto slow mode*
7
Remaining battery indicator
Charging a USB device from a
electrical outlet (UC18YSL3)
Charging a USB device and battery
from a electrical outlet (UC18YSL3)
How to recharge USB device
(UC18YSL3)
When charging of USB device is
completed (UC18YSL3)
Selecting accessories
*1 How to use the hook
CAUTION
Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
When electing to carry the tool hooked to your hip belt,
make sure to detach the tool socket. Failure to do so
may result in unexpected injury.
*2 Installing a socket
(1) Slide the O-ring out of the groove, then align the hole of
the socket with the hole of the anvil and insert the anvil
into the socket.
(2) Insert the pin into the socket.
(3) While making sure that the pin doesn't fall, attach the O-
ring to the groove on the socket.
*3 Reversing the rotational direction
NOTE
The push button can not be switched while the power
tool is turning. To switch the push button, stop the
power tool, then set the push button.
*4 How to use the LED light
To prevent the battery power consumption caused by
forgetting to turn off the LED light, the light goes off
automatically about 10 seconds after your finger is
released.
*5 Tightening mode selector function
CAUTION
Select tightening mode while the trigger switch is
released. Failure to do so could result in malfunction.
NOTE
○ The appropriate mode will vary depending on the screw
and the material being screwed. Adjust the tightening
mode setting by test-tightening a number of screws.
Figure
3
4
5
6
3
7
8
4
9
5
10
11
12
13
14-a
14-b
15
16
—
○ The tightening mode cannot be changed unless the
rechargeable battery has been mounted in the tool and
the switch has been pulled.
(1) High / Low mode selector switch (Fig. 10-a, Table 5)
Page
The tightening mode switches between 4 different
rotation speeds each time the High / Low mode selector
2
switch is pressed.
2
Table 5: High / Low mode selector function setting
3
Indicator
3
lamps
3
1
3
4
4
2
4
4
3
5
5
4
5
5
(2) Auto stop mode selector switch (Fig. 10-b)
Each time the auto stop mode selector switch is
pressed, the auto stop function will switch between ON
5
and OFF.
*6 Auto stop mode (Table 6)
Stops automatically after a preset time has elapsed.
18
Push the Push button to the forward ("R") position, then
press the Auto stop mode selector switch to select the
setting.
Table 6: Auto stop mode settings and functions
Indicator
lamps
1
2
3
4
*7 Auto slow mode (Table 7)
Stops for a preset time and/or changes the speed
automatically to a preset speed.
Push the Push button to the reverse ("L") position, then
13
Maximum
unloaded speed
For work that
1200 /min
requires fine
adjustments.
1800 /min
For work that
requires the
power to be
suppressed.
2400 /min
2800 /min
For work that
(WR18DH)
requires power
3000 /min
and speed.
(WR36DH)
Maximum
Auto stop
unloaded
time
speed
1200 /min
1800 /min
0.5 sec.
2400 /min
2800 /min
(WR18DH)
1.0 sec.
3000 /min
(WR36DH)
Uses
Uses
(For
temporary
tightening
etc.)
Small
diameter
bolts
Vehicles
wheel nut
or piping
Heavy
machinery
or steel
frame