KitchenAid Architect Series II KFGS366VSS Руководство по установке - Страница 7

Просмотреть онлайн или скачать pdf Руководство по установке для Варочная панель KitchenAid Architect Series II KFGS366VSS. KitchenAid Architect Series II KFGS366VSS 20 страниц. 30" (76.2 cm) and 36" (91.4 cm) gas built-in cooktop
Также для KitchenAid Architect Series II KFGS366VSS: Размеры (1 страниц), Руководство по измерению (1 страниц)

Печатать страницу

3. Select bracket mounting holes that will allow the bracket to

extend far enough out from the cooktop for the installation of

2½" (6.4 cm) clamping screws.

A. Cooktop

B. Cooktop base

C. Attachment screw

D. Clamping bracket (extends far enough beyond

cooktop base to allow installation of clamping screws)

E. 2½" (6.4 cm) clamping screw (to be installed in "Attach

Cooktop to Countertop")

F. Countertop

4. Attach brackets to cooktop base bottom with bracket

attachment screws using the bracket mounting holes

selected in Step 3. Securely tighten screws.

Make Gas Connection

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

To Assemble Pressure Regulator:

1. Using 2 or more people, stand the cooktop on its side or

back.

2. Connect the flexible stainless steel connector to the pressure

regulator using a ½" male pipe thread adapter and nipple.

A combination of pipe fittings must be used to connect the

cooktop to the existing gas line. Shown following is a typical

connection. Your connection may be different, according to

the supply line type, size and location.

3. Install the pressure regulator with the arrow pointing up

toward the bottom of the cooktop base and in a position

where you can reach the regulator cap.

IMPORTANT: All connections must be wrench-tightened. Do

not make connections to the gas regulator too tight. Making

the connections too tight may crack the regulator and cause

a gas leak. Do not allow the regulator to turn on the pipe

when tightening fittings.

Use only pipe-joint compound made for use with Natural and LP

gas.

Do not use TEFLON

required depending on your installation.

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see G

in the following illustration).

2. Attach 1 adapter and nipple to the gas pressure regulator and

the other adapter and nipple to the gas shutoff valve. Tighten

both adapters and nipples.

3. Use a

flexible connector to the adapters. Check that connector is

not kinked.

Complete Connection

1. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

2. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

A. Access cap

B. Rear of cooktop

C. Gas pressure regulator

D. Up arrow. Regulator must be installed with

arrow pointing up to cooktop bottom.

tape. You will need to determine the fittings

" combination wrench and pliers to attach the

A. " nipple

E. Gas pressure regulator

B. " adapter

F. ½" adapter

C. Flexible connector

G. Use pipe-joint compound.

D. ½" nipple

H. Manual gas shutoff valve

A. Closed valve

B. Open valve