Decko 24000-DKO Руководство пользователя - Страница 10
Просмотреть онлайн или скачать pdf Руководство пользователя для Открыватель двери гаража Decko 24000-DKO. Decko 24000-DKO 14 страниц. Handles doors 18 ft. wide & up to 7ft.tall
Печатать страницуAttaching Door Arms
!
To prevent SERIOUS INJURY:
- DO NOT connect power until instructed.
- Keep hands and fingers away from the sprocket during operation.
- Wear gloves when installing chain and cable.
- Keep hands and fingers away from joints and possible sharp edges.
Min. 8" (20cm)
2
3
5
Straight Door Arm
6
Curved Door Arm
1
4
2
4
PULL
Disconnect
5
Bolt 5/16" - 18x1"
Flange Nut
Hitch Pin
Clevis Pin - 5/16" x 1"
Fig.1
10
WARNING
To Connect Door Arm
Follow the steps shown in Fig. 1
1. CLOSE the door.
2. Move the Emergency Release lever to the downward position
to disconnect the Trolley from Trolley Shaft.
3. Slide the Trolley so that it is about 8" (20cm) from the Pulley.
4. Fasten the Curved Door Arm to the door Bracket with
5/16" x 1"Clevis Pin and lock it with a Hitch Pin.
5. Fasten the Straight Door Arm to the Trolley with a
5/16" x 1" Clevis Pin and lock it with a Hitch Pin.
6. To connect the door arms together, choose two pairs of holes
which are as far apart as possible. Fasten the arms using two
5/16" x 1" Bolts and Flange Nuts.
Programming Hand-held Transmitter
!
To Prevent SERIOUS INJURY or DEATH:
- Keep Transmitter and battery out of reach of children.
- NEVER permit children to access the Push Button nor remote Transmitters.
- Operate the door ONLY when it is properly adjusted, and there are no obstructions present.
- ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door.
To reduce risk of fire, explosion or electric shock:
- DO NOT short circuit, recharge, dissemble or heat the battery.
- Replace with 23AE 12 Volt batteries ONLY. Dispose of batteries properly.
Signal and Battery
Indicator
Visor Clip
Holster
Fig.1
LEARN
30
seconds
Fig.2
x2
Fig.3
23AE 12 Volt
Alkaline Battery
Fig.4
WARNING
To Program Transmitter(s):
1.
See Fig.2 to add a Transmitter. Press the "LEARN" button
on the rear control panel of the Opener. The courtesy light
will illuminate with an audible click*. The unit is now ready
to learn a Transmitter.
2.
Within 30 seconds, press the button on the Transmitter.
3.
The courtesy light will flash twice indicating Transmitter
has been stored successfully**.
Up to 20 Transmitters (including wireless keypad codes) can be
added to the unit by repeating the above procedures.
If more than 20 Transmitters are stored, the first stored
Transmitter will be replaced. (i.e. the 21st Transmitter replaces
the 1st stored Transmitter.)
* If the courtesy light is already on, it will flash once and stay
illuminated for 30 seconds.
** If a Transmitter is not accepted, the courtesy light will stay on
for 30 seconds, flash 4 times and then stay on for 2-1/2
minutes. Retry programming the Transmitter by repeating the
steps above.
Removing ALL Transmitters:
To remove ALL Transmitters from memory, press and hold the
"LEARN" button for 5 seconds. The courtesy light will flash 7
times indicating ALL Transmitters have been removed from
memory.
Replacing Transmitter Battery:
When the battery of the hand held Transmitter is low, the
indicator light will become dim and/or the range of the
Transmitter will diminish. To replace the battery, remove the
battery cover from the Transmitter as shown in Fig 4. Replace
with a 23AE 12 volt alkaline battery with polarity shown in Fig.4.
This device complies FCC Rules for HOME OR OFFICE USE. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
19