KitchenAid KGCP487JSS0 Руководство по установке - Страница 8

Просмотреть онлайн или скачать pdf Руководство по установке для Варочная панель KitchenAid KGCP487JSS0. KitchenAid KGCP487JSS0 9 страниц. 36" (91.4 cm) and 48" (121.9 cm) professional gas cooktop for residential use only
Также для KitchenAid KGCP487JSS0: Список деталей (4 страниц)

Печатать страницу

E_ectronic

_gnition

System

initiam mighting

Cooktop burners use electronic igniters in

place of standing pilots. When the

cooktop control knob is pushed in and

turned to the "LITE" position, the system

creates a spark to light the burner. This

sparking continues until the control knob

is turned to the desired setting.

m Check operation of the cooktop

burners. Push in and turn each control

knob to "LITE" position. The flame should

light within 4 seconds. Do Not leave the

knob in the "LITE" position after

burner lights,

If burners do not light properly, turn

control knob to the "OFF" position. Check

that burner cap is in the proper position.

Check that power supply cord is plugged

in and that circuit breaker or house fuse

has not blown. Check that the shutoff

valve is in the "ON" position. Check

operation again. If a burner does not light

at this point, contact your KitchenAid

dealer for assistance.

Push in and turn each control

knob to the "LO" (or simmer) setting. The

'%0" setting of each burner has been

factory set to the lowest setting possible

to provide a stable flame. If it does not

stay lit on the '%O" setting, check '%O"

setting as follows:

a. Turn control to "LITE" until burner

ignites.

b. Quickly turn knob down to LOWEST

POSITION.

c. If burner goes out, readjust valve as

follows:

Remove the burner control knob. Insert a

flat-blade screwdriver into the hollow

valve stem and engage the slotted screw.

Flame size can be increased or

decreased by turning the screw. Adjust

flame until you can quickly turn knob from

the "Hi" to '%0" position without

extinguishing the flame. Flame should be

as small as possible without going out.

Installer checkeff

COOKTOP

[_]

Cooktop correctly positioned in

countertop cutout.

Maintained specified distances to

cabinet surfaces.

Cooktop level = front to back = side

to side.

Burner caps positioned properly on

sealed burner bases.

[_AII

packing material removed.

[_]

Backguard or island trim attached

(see page 4).

Polarized and grounded 120-volt,

60-Hz, AC, 15-amp fused electrical

supply for power supply cord

connection.

GAS SUPPLY

[_]

Connection: 1/2" NPT with a

minimum 5/8" (1&9 mm)diameter

flex line.

[_The

cooktop is connected only to

type of gas for which it is certified for

use.

[_]

Check that the circuit breaker is not

tripped or the house fuse blown.

Check that the power supply cord is

plugged into the outleL

Check that gas valves are turned to

the "ON" position.

[_See

Use and Care Guide for

troubleshooting list.

If you need

The KitchenAid ConsumerAssistanceCenter

will answer any questionsabout operatingor

maintainingyour cooktop not covered in the

Installation Instructions.The KitchenAid

ConsumerAssistanceCenter is open 24

hours a day, 7 days a week.Just dial 1-800-

422-1230 -- the call is free within the

continentalUnited States, or visit our web site

at v_'w.kitchenaid, c om.

When you call, you wil! need the cooktop

model numberand serial number. Both

numberscan be found on the model/serial

rating plate located on the bottom of the

cooktopand are visible through the cutout in

the left-hand back corner of the enclosure

bottom.

In the event that your KitchenAid

appliance should need service, call the

dealer from whom you purchased the

appliance or a KitchenAid-designated

service company. A KitchenAid-

designated service company is listed in

theYellow Pages of your telephone

directory under "Appliances --

Household -- Major -- Service and

Repair:'

You can also obtain the service

company's name and number by dialing,

free within the continental United States,

the KitchenAid Consumer Assistance

Center telephone number, 1-800o422-

1230.A special operator will tell you the

name of your nearest KitchenAid-

designated service company.

Maintain the quality built into your

KitchenAid appliance -- call a

KitchenAid-designated service company.

if removing the cooktop is necessary for

maintenance, shut off gas supply.

Disconnect the gas and electric supply.

After disconnecting the gas and electric

supply, finish removing the cooktop.

Generally, the cooktop does not need to

be removed for servicing.