KitchenAid KICU509XSS Руководство по установке - Страница 2
Просмотреть онлайн или скачать pdf Руководство по установке для Варочная панель KitchenAid KICU509XSS. KitchenAid KICU509XSS 16 страниц. 30" (76.2 cm) and 36" (91.4 cm) electric
Также для KitchenAid KICU509XSS: Размеры изделия (1 страниц), Руководство по установке (12 страниц), Руководство по измерению (8 страниц)
Печатать страницу
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Tape measure
■
Flat-blade screwdriver
■
Phillips head screwdriver
■
Hand or electric drill
■
Level
■
Parts supplied
Brackets (2)
■
2
⁄
" (6.4 cm) clamping screws (4)
1
■
2
#8 x 3/8" (9.5 mm) sheet metal screws (4)
■
Parts needed
A UL listed or CSA approved strain relief
■
UL listed wire connectors
■
A UL approved junction box or 240 V outlet
■
Cooktop Bracket Adhesive Kit Part Number W10310006
■
if installing the cooktop into a marble countertop. See the
"Assistance or Service" section of the Use and Care Guide
for information on ordering.
Check local codes. Check existing electrical supply. See
"Electrical Requirements."
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
Location Requirements
Make sure you have everything needed for correct installation. It
is the responsibility of the installer to comply with the installation
clearances specified in these instructions.
IMPORTANT: Observe all governing codes and ordinances.
When installing cooktop, use minimum dimensions given.
To eliminate the risk of burns or fire by reaching over the
■
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
It is the installer's responsibility to comply with installation
■
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the underside of the
cooktop burner box.
2
05-Sep-2019 13:08:05 EDT | RELEASED
INSTALLATION REQUIREMENTS
Marker or pencil
■
Pliers
■
1/4" drill bit
■
Jigsaw
■
In some European factories the letter "W" of the part code mentioned herein will be automatically
30" (76.2 cm) cooktop model/serial rating plate
location (models JIC4430 and KICU509)
A
A. Model/serial rating plate location
36" (91.4 cm) cooktop model/serial rating plate
location (models JIC4536 and KICU569)
A
A. Model/serial rating plate location
Check the cooktop base for an approved installation label.
■
Verify approved oven model numbers that can be installed
with your cooktop model number. If you do not find this
label, your cooktop may not be approved for use over an
undercounter built-in oven. Contact your dealer to confirm
that your cooktop is approved.
Ovens approved for this type of installation will have an
■
approval label located on the top of the oven. If you do
not find this label, contact your dealer to confirm that your
oven is approved. Refer to oven manufacturer's Installation
Instructions for approval for built-in undercounter use and
proper cutout dimensions.
When installing cooktop over an undercounter built-in oven,
■
do not fasten cooktop to countertop with clamps or seal
cooktop to countertop. This will make the cooktop easier to
remove if future servicing becomes necessary.
Use the countertop opening dimensions that are given
■
with these Installation Instructions. Given dimensions are
minimum clearances and provide 0" (0 cm) clearance.
Grounded electrical supply is required. See "Electrical
■
Requirements" section.
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")