Green Mountain Grills Prime Руководство пользователя - Страница 13

Просмотреть онлайн или скачать pdf Руководство пользователя для гриль Green Mountain Grills Prime. Green Mountain Grills Prime 14 страниц. Wood fired pellet grills

Печатать страницу

TROUBLESHOOTING

Grill doesn't turn on when you press the power button.

Check to make sure the power cord is plugged in. When the AC adapter is plugged into the wall, check that the

light on the adapter comes on.

Inspect both ends of the male-to-male power cord to ensure the connections aren't compromised.

Check the circuit breaker and/or GFCI on the circuit the adapter is plugged into. Plug a small appliance into the

same outlet to see if you have electricity.

Unplug the grill. Remove the control panel. Check for loose wires connected to the wiring harness. Disconnect and

reconnect the wiring harness to ensure a secure connection.

Grill doesn't come up to temperature.

If grill remains at ambient temperature...

Check the firebox to see if it has overflowed with pellets. If it has, clean it out and start over. This overfill can result

from turning the grill off without using the fan mode or from charging the firebox when it does not need to be

charged. Reread the section on "Priming the Firebox" to understand that. You only need to prime the firebox the

first time you use the grill or on any subsequent occasions when it runs out of pellets and the auger runs until

empty.

If grill lights, but does not reach set temperature...

Check the combustion fan to ensure it spins freely and there is no damage to the blades.

Ensure the heat shield is properly installed.

9.25 in.

4.25 in.

DANIEL BOONE

JIM BOWIE

Ensure the grease tray is installed correctly.

Jim Bowie & Daniel Boone

GREENMOUNTAINGRILLS.COM

Improper shield placement will result in issues coming to

temperature. When using the heat shield adjustment rod,

a centered heat shield should be positioned approximately

at the "-0.5" mark on the rod. The depth to which the rod is

threaded into the receiving nut varies, so some

experimenting might be needed to find the perfectly

adjusted center point on your rod.

Erratic temperature.

If the digital display reads "SEN" or shows rapid fluctuation in temperature (faster than the grill could realistically

increase/decrease its internal temperature) call our technical support 530-347-9167 opt. 1.

Otherwise, check to make sure you do not have aluminum foil on the grease tray that is blocking the thermal

sensor. It is okay to wrap your tray in foil. However it must be wrapped tight to the metal, and the hole as well as

the half-moon cutout must be punched out of the foil to ensure proper airflow.

A simple way to check the thermal sensor is to look at the initial temperature reading the grill gives after the

0-1-2-3 start-up process. This temperature should be close to the ambient air temperature since the grill has not

yet had a chance to heat up.

Improper shield placement will result in issues coming to temperature. When using the heat shield adjustment rod,

a centered heat shield should be positioned approximately at the "0" mark on the rod. The depth to which the rod is

threaded into the receiving nut varies, so some experimenting might be needed to find the perfectly adjusted "0"

point on your rod.

Ensure the grease tray is installed correctly. See the previous page for proper installation.

Smoke is coming out of the hopper.

Make sure your burn pot is empty of ash and pellets.

Make sure the hopper lid stays closed when you have the grill on. Press firmly down on each of the corners of the

lid to make certain it is closed tight. If a corner of the lid sits up even 1/8 inch while the lid is flat, a warped hopper

lid is your issue.

You can test this by running 2 sheets of tin foil over your hopper then closing the lid down on top of the foil to make

a temporary seal, hopefully preventing smoke from traveling through your hopper.

Ensure the combustion fan spins freely and is not damaged.

Ensure the pellet dump door is closed tight.

If all else fails, the square gasket seal between the hopper and auger may be the culprit. You can seal with

high-temp silicone.

Low pellet alarm beeps continuously.

Fill the hopper with pellets so that their level is above the low pellet sensor. If this does not solve the problem,

unplug the grill then disconnect the alarm from and reconnect it to the back of the control panel. If the beeping

persists, your alarm is broken and needs to be replaced. Contact our technical support 530-347-9167 opt. 1. In the

meantime, you can stop the beeping by unplugging the low pellet alarm from the circuit board and leaving it

disconnected.

*The low pellet alarm is not necessary for the grill's functionality. You can leave the alarm disconnected and

continue cooking.