IKEA W10502581D Руководство по эксплуатации и уходу - Страница 8
Просмотреть онлайн или скачать pdf Руководство по эксплуатации и уходу для Вентиляционная вытяжка IKEA W10502581D. IKEA W10502581D 48 страниц. 30"(76.2cm) island-mount canopy range hood
Печатать страницу
Range Hood Mounting
Screws Installation
1. Determine and mark the centerline on the ceiling where the
range hood will be installed, considering the requirements for
ceiling support structures. See the "Location Requirements"
section. Make sure the range hood is centered over the
cooking surface.
2. Tape template in place on the ceiling at the marked
centerline. The line for the front of the range hood should be
parallel to the front of the cooktop.
3. Use a pencil to mark the mounting screws, wire access and
duct hole locations on the ceiling.
NOTE: Mounting hole locations should be into a ceiling
support structure capable of holding 80 Ibs (36.6 kg).
Remove the template.
4. Drill 4 - 3/le" (4.8 mm) pilot holes for mounting the upper
horizontal support.
Complete
Preparation
1. Determine the required location for the home power supply
cable and drill a 1/2"(1.3 cm) diameter hole for wire access.
2. Run 1/2"(1.3 cm) conduit and wires or home power supply
cable according to the National Electrical Code or CSA
Standards and local codes and ordinances. There must be
enough 1/2"conduit and wires or home power supply cable
from the fused disconnect (or circuit breaker) box to make the
connection in the hood's electrical terminal box.
NOTE: Do not reconnect power until installation is complete.
3. For vented installations only: Using a jigsaw or keyhole
saw, cut a 61/2 '' (16.5 cm) diameter hole for the vent duct.
4. Attach the upper horizontal support bracket with 4 - 5 x
45 mm #2 Phillips wood screws.
NOTE: Upper horizontal support screws must be into a
ceiling support structure capable of holding 80 Ibs (36.6 kg).
A
_B
1. Position the 4 vertical supports (A) with the notches at the
bottom and attach to the range hood using 16 - 4.2 x 8 mm
T20 ®screws. Use a T20 ®Torx ® drive (or T20 ® adapter
provided) to tighten all assembly screws.
2. Attach the horizontal support (B) using 8 - 4.2 x 8 mm T20 ®
screws.
3.
im
A
B
.............
_a
A
........
_a
A. Verficalsuppor_
B. Horizon_l
support
C. Notched end
Attach a second set of vertical supports (A) and set the
vertical height (B). See "Installation Dimensions"
in the
"Location
Requirements" section to help determine the
desired dimension for vertical height "B."
Secure with 16 - 4.2 x 8 mm T20 ®screws.
A
I
A. Vertical supports
B. Vertical height
B
1.
Non-Vented
(recirculating)
Installation
Attach the air deflector to the upper horizontal support using
2 - 4.2 x 8 mm T20 ®mounting screws.
B
A. Upper horizontal support
B. 5 x 45 mm screws (#2 Phillips drive)
2.
A. Deflector
B. 2
4.2x8mm
®
-
T20 mounting screws
Measure the length of 6" (15.2 cm) duct needed to connect
the transition to the deflector.
NOTE: Vent should fit up inside the deflector 1" (2.5 cm)
minimum.
8