IKEA finputsad Руководство - Страница 6
Просмотреть онлайн или скачать pdf Руководство для Посудомоечная машина IKEA finputsad. IKEA finputsad 12 страниц. Integrated
Также для IKEA finputsad: Руководство (20 страниц), Руководство по эксплуатации (36 страниц), Руководство (33 страниц), Руководство (29 страниц)
Печатать страницу
ENGLISH
not be obstructed by a carpet.
If installing the dishwasher at the end
of a row of units making the side panel
accessible, the hinge area must be covered
to avoid risk of injury.
The inlet water temperature depends on
the dishwasher model. If the installed inlet
hose is marked "25°C Max", the maximum
allowed water temperature is 25°C. For all
other models the maximum allowed water
temperature is 60°C. Do not cut hoses
and, in the case of appliances fitted with
a waterstop system, do not immerse the
plastic casing containing the inlet hose
in water. If hoses are not long enough,
contact your local dealer. Make sure the
inlet and drain hoses are kink-free and are
not crushed. Before using the applinace
for the first time, check the water inlet and
drain hose for leaks. Make sure that the
four feet are stable and resting on the floor,
adjusting them as required, and check that
the dishwasher is perfectly levelled using a
spirit level.
Use the appliance only when the covers
shown on diagram 19 in the Assembly
instruction are correctly assembled - risk of
injury.
ELECTRICAL WARNINGS
The rating plate is on the edge of the
dishwasher door (visible when the door is
open).
It must be possible to disconnect
the appliance from the power supply by
unplugging it if plug is accessible, or by
a multi-pole switch installed upstream of
the socket in accordance with the wiring
rules and the appliance must be earthed in
conformity with national electrical safety
standards.
Do not use extension leads, multiple
sockets or adapters. The electrical
components must not be accessible to
the user after installation. Do not use the
appliance when you are wet or barefoot.
Do not operate this appliance if it has a
damaged power cable or plug, if it is not
working properly, or if it has been damaged
or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard
- risk of electrical shock.
If the fitted plug is not suitable for your
socket outlet, contact a qualified technician.
Do not pull the power supply cable. Do not
immerse the mains cord or plug in water.
Keep the cord away from hot surfaces.
ELECTRICAL CONNECTION FOR GREAT
BRITAIN AND IRELAND ONLY
Fuse replacement.
If the mains lead of this appliance is fitted
with a BS 1363A 13amp fused plug, to
change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS1362 type and
proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
A
B
Important:
The fuse cover must be refitted when
changing a fuse and if the fuse cover is lost
the plug must not be used until a correct
replacement is fitted.
Correct replacement are identified by
the colour insert or the colour embossed
in words on the base of the plug.
Replacement fuse covers are available from
your local electrical store.
For the Republic of Ireland only
The information given in respect of Great
Britain will frequently apply, but a third type
of plug and socket is also used, the 2-pin,
side earth type.
Socket outlet / plug (valid for both
countries)
If the fitted plug is not suitable for your
socket outlet, please contact After-sales
Service for further instruction. Please do
not attempt to change plug yourself. This
procedure needs to be carried out by a
qualified technician in compliance with
the manufactures instructions and current
standard safety regulations.
6