IKEA IUD9500WX0 Руководство по установке - Страница 5
Просмотреть онлайн или скачать pdf Руководство по установке для Посудомоечная машина IKEA IUD9500WX0. IKEA IUD9500WX0 44 страницы. Undercounter dishwasher plastic giant tub models
Также для IKEA IUD9500WX0: Инструкции пользователя (25 страниц)
![IKEA IUD9500WX0 Руководство по установке](/uploads/products/server2/2083615/2083615.jpg)
odp©/y
•
A hot water line with 20-120
psi (138-862
kPa) water pressure.
•
120°F (49°C) water temperature
at dishwasher.
•
Flexible stainless steel braided fill line
(1/2"
minimum plastic
tubing is not recommended).
Contact a qualified electrician.
Ensure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
You must have:
•
120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply.
•
Copper wire only.
We recommend:
•
A time-delay fuse or circuit breaker.
•
A separate circuit.
If direct wiring dishwasher:
•
Use flexible, armored or nonmetallic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
Use strain relief method provided with house wiring junction
box or install a UL-listed/CSA-certified
clamp connector to the
house wiring junction box. If using conduit, use a
UL-listed/CSA-certified
conduit connector.
If connecting
dishwasher
with a power supply cord:
•
Use Power Supply Cord Kit (Part Number 4317824) marked
for use with dishwashers. Kit contents include:
•
Voltex, Inc., UL listed 16 gauge 3 wire power supply cord
with 3 prong grounded plug.
•
Neer C-500 _/2'strain relief.
•
3 wire connectors.
•
Part Number 302797 grommet.
Follow the kit instructions for installing the power supply cord.
Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the dishwasher
opening. Outlet must meet all local codes and ordinances.
INSTALLATIONINSTRUCTIONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect
power.
2. Turn off water supply.
/,,Js t_9 ®xsn 9 u
ty hookups
Follow the steps in the section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
If you are installing the dishwasher in a cabinet opening that
does not have utility hookups, follow the steps under "Prepare
cabinet opening where there are no existing utility hookups"
section.
1. Check that the water line reaches to the front left of the
opening where the water connection will be made.
A. Water line
B. Direct wire
2. Check that the direct wire reaches to the front right of opening
where the electrical connection will be made.
If the water line and direct line wire reach far enough into the
opening, proceed to the next section, "Install the Drain Hose." If
they do not reach far enough, follow the steps under "Prepare the
Cabinet Opening Where There are no Existing Utility Hookups."
Install the Drain Hose
IMPORTANT: Always use a new drain hose even when installing a
new replacement dishwasher.
1. Drill a 1V2" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
2=
i/
i
Connect drain hose to waste tee or waste disposer using one
of the following methods:
5