Makita 3706 Руководство по эксплуатации - Страница 6

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Электроинструмент Makita 3706. Makita 3706 14 страниц. Cutout tool
Также для Makita 3706: Руководство по эксплуатации (10 страниц), Руководство по эксплуатации (2 страниц), Руководство по эксплуатации (17 страниц), Руководство по эксплуатации (13 страниц), Руководство по эксплуатации (12 страниц)

Печатать страницу

Adjusting depth of cut (Fig. 3)

CAUTION:

Always be sure that the tool is switched off and

unplugged before adjusting depth of cut.

To adjust the shoe, turn the thumb screw to loosen. Slide

the shoe to the desired position and tighten the thumb

screw securely. Check for the proper clearance beneath

the workpiece before cutting so that the bit will not strike

a hard surface such as the floor, workbench, etc.

Switch action (Fig. 4)

CAUTION:

Before plugging in the tool, always check to see that the

switch lever actuates properly and returns to the "OFF"

position.

To start the tool, move the switch lever to the "ON" posi-

tion. To stop the tool, move the switch lever to the "OFF"

position. This can be done in the forward area of the

switch lever or by bumping off the rear area of the switch

lever.

OPERATION

CAUTION:

• Avoid forcing the bit to bend or twist. It may snap.

• Before turning the tool on, make sure the bit and collet

nut are securely tightened.

Hold the tool secure with the bit pointing in a safe direc-

tion not contacting any surface and slide the switch to the

"ON" position. Wait until the tool attains full speed.

When starting the multipurpose bit into the material, hold

the tool at approximately a 45 degree angle with the edge

of the shoe base contacting the material. (Fig. 5)

Carefully bring the tool to a straight position so the shoe

base is in full contact with the material. (Fig. 6)

When inserting the drywall guide bit into the drywall,

carefully insert the bit straight until the shoe base is in full

contact with the material. (Fig. 7)

Move the tool slowly with a constant pressure in a clock-

wise direction to make the cut.

When cutting straight line, clamp a straight board firmly

to the material and use it as a guide. Move the tool in the

direction of the arrow with the shoe base flush with the

side of the guide board. (Fig. 8)

When the cut is complete, turn the tool off and wait for

the bit to stop rotating and then carefully remove it from

the material.

NOTES:

When using this tool, the rotating action causes the

tool to pull. The less pressure applied to the tool

causes less pull and provides a more accurate cut.

Excessive pressure or fast cutting can cause the bit

to dull or break premature.

When cutting drywall around outlet boxes, cut in a

counterclockwise direction for ease of cut.

The standard bit included with this tool is for cutting

drywall only. When cutting materials other than dry-

wall, do not use the standard drywall guide bit.

Circular guide

Circular cutting diameters: 10 cm – 34 cm

Installing circular guide

Release the thumb screw which serves to secure the

shoe. (Fig. 9)

Align the projections in the circular guide with the

grooves in the shoe, and secure the shoe and circular

guide using the thumb screw. (Fig. 10)

To adjust the cutting depth, proceed first by loosening the

thumb screw and then by sliding the shoe and circular

guide together. (Fig. 11)

After completion of the adjustment, tighten the thumb

screw securely.

Operation

Loosen the knob, and adjust its position in accordance

with the size of the circle to be cut. (The hole dimensions

to be cut are indicated on the side of the circular guide as

a general guideline.) (Fig. 12)

After completion of the adjustment, tighten the knob

securely.

Insert the end of the knob into the centre of the circle to

be cut, and proceed to cut in a clockwise direction.

(Fig. 13)

Vacuum cover

Cleaner operations can be performed by connecting the

cutout tool to Makita vacuum cleaner or dust collector.

Installing vacuum cover (Fig. 14)

Loosen the thumb screw and remove the shoe. Attach

the vacuum cover, and fasten it securely using the thumb

screw.

Installing vacuum cover with circular guide

Release the thumb screw which serves to secure the

vacuum cover. Align the projections in the circular guide

with the grooves in the vacuum cover, and secure the

vacuum cover and circular guide using the thumb screw.

(Fig. 15)

To adjust the cutting depth, proceed first by loosening the

thumb screw and then by sliding the vacuum cover and

circular guide together.

After completion of the adjustment, tighten the thumb

screw securely. (Fig. 16)

Connecting to Makita vacuum cleaner or dust

collector

Connect the hose of a vacuum cleaner/dust collector to

the dust nozzle. When connecting to Makita vacuum

cleaner, an optional hose 28 mm in inner diameter is

necessary. (Fig. 17)

When connecting to Makita dust collector, connect the

hose for the dust collector directly to the dust nozzle.

(Fig. 18)

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Centre.