ALIBI ALI-NS2114L Руководство по быстрой установке - Страница 3

Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Камера безопасности ALIBI ALI-NS2114L. ALIBI ALI-NS2114L 7 страниц. 4mp white light ip turret camera

Печатать страницу

ALIBI ALI-NS2114L Руководство по быстрой установке

Note: In the screen above, the tool can discover devices on other subnets. It will also list other

Alibi compatible devices on the LAN, and devices with the address 192.168.1.64 (an inactive Alibi

device).

Step 5.

Activate Inactive Alibi device

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.

Refer to the documentation available for your NVR firmware for the procedure to activate the camera, if

necessary.

When an Alibi device is first installed, or reset to its factory configuration, it must be "Activated" before

it can be used. In the Alibi Configuration Tool, "Inactive" devices have a Security status of Inactive,

and an IPv4 address of 192.168.1.64. A device is "Activated" when a password is assigned to the

admin username of the device.

In the example below, an ALI-NS2114L camera is activated and configured for its network. The

procedure is similar for all other Alibi network cameras currently available.

Scan through the list of devices the Alibi Config Tool discovered for the Inactive device you want

to activate (see below). Click on the device in the list to highlight it, and then click the select box

to check it. See below.

Selected

Activate

Click the Activate button. In the Activate window, you will create a password for the admin

(administrator) username.

In the Activate window, enter an a password for admin in the New Password field.

Include a combination of uppercase, lowercase alphabetic characters and numbers to

create a "Strong" password. The rating is shown beneath the Password field. See above.

Enter the admin password again in the Confirm field, and then click Activate. In the

screen below, notice that the device Security status shows "Active". Record your admin

password for reference later.

If you lose your admin (administrator) password, you cannot configure the device or restore



it to its factory settings. To reset your password, call your support organization for specific

CAUTION

instructions.

www.observint.com

Notice that although the device is now activated, it retained the default IP address.

Step 6.

Edit Network Parameters

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this

step. The camera will receive network configuration settings from the NVR. Refer to the documentation

available for your NVR firmware for more information.

You can change the network parameters of devices that are active.

In the list of devices discovered, click on the device you want to change the network settings for,

and then click the select box to check it. See below.

Edit Network Parameters

In the popup window, edit the current network parameters, and then enter the Administrator

(admin) user password in the field at the bottom.

Enable DHCP: You can select Enable DHCP to acquire compatible network settings

from a DHCP server installed on the LAN. However, these settings might be changed later

by the DHCP server. Since it is recommended to use an unchanging IP address, you can use

DHCP to acquire compatible network settings, and then uncheck Enable DHCP and save

that configuration to retain the new network parameters.

In the example below, Enable DHCP was checked to acquire compatible network

settings from the DHCP server.

Click OK to save your settings. The parameter change(s) will be shown device's network

parameters (see below).

Step 7.

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.

Microsoft® IE is used to access your camera remotely. IE must run as an Administrator to use all features

available through a remote login to the camera.

Setting MS Internet Explorer to run as an Administrator

Window 7: To run IE as an Administrator:

Find or create an IE icon on your computer desktop.

Hold down the shift key, and then right-click on the IE icon.