KitchenAid 30" Freestanding Range Руководство по установке - Страница 4

Просмотреть онлайн или скачать pdf Руководство по установке для Печь KitchenAid 30" Freestanding Range. KitchenAid 30" Freestanding Range 8 страниц. (61cm), (68.6cm), and (76.2cm) indoor/outdoor electric warming drawer
Также для KitchenAid 30" Freestanding Range: Инструкции по установке (5 страниц), Руководство по установке (13 страниц), Инструкции по установке (5 страниц), Руководство по установке (16 страниц)

Печатать страницу

Gas supply

requirements

WARNING

Explosion Hazard

Use a new AGA or CSA approved gas

supply line.

Install a shutoff valve.

Securely tighten all gas connections.

If connected to L.P. have a qualified person

make sure gas pressure does not exceed

14" water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death,

explosion, or fire.

In the State of Massachusetts, the following

installation instructions apply:

• Installations and repairs must be performed by

a qualified or licensed contractor, plumber, or

gasfitter qualified or licensed by the State of

Massachusetts.

• If using a ball valve, it shall be a T-handle

type.

• A flexible gas connector, when used, must not

exceed 3 feet.

Observe all governing codes and ordinances.

IMPORTANT: Range must be connected to a

regulated gas supply.

This installation must conform with local

codes and ordinances. In the absence of

local codes, installations must conform

with American National Standard, National Fuel

Gas Code ANSI Z223.1 — latest edition or CANI-

B149 — latest edition* installation codes.

Input ratings shown on the model/serial

rating plate are for elevations up to 2,000

feet (609.6 m). For elevations above

2,000 feet (609.6 m), ratings are reduced at a rate

of 4% for each 1,000 feet (304.8 m) above sea

level. (Not applicable for Canada.)

This range is equipped for use with

Natural gas. It is design-certified by

AGA/CSA for Natural and L.P. gas with

appropriate conversion. The model/serial rating

plate, located on the oven frame behind the

drawer, has information on the type of gas that can

be used. If this information does not agree with the

type of gas available, check with your KitchenAid

dealer.

Provide a gas supply line of 3/4" (1.9 cm)

rigid pipe to the range location. A smaller

size pipe on long runs may result in

insufficient gas supply. Pipe-joint compounds

appropriate for use with L.P. gas must be used.

With L.P. gas, piping or tubing size can be 1/2"

(1.3 cm) minimum. L.P. gas suppliers usually

determine the size and materials used on the

system.

Copies of the standards listed may be obtained from:

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

Panel C

If local codes permit, a new AGA/CSA

design-certified, 4-5 foot (122 -152.4 cm)

long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D.,

flexible metal appliance connector is

recommended for connecting this range to the gas

supply line. Do Not kink or damage the flexible

tubing when moving the range. A 1/2" (1.3 cm)

male pipe thread is needed for connection to

pressure regulator female pipe threads.

shutoff valve

"open" position

to gas supply

The supply line shall be equipped with an

approved shutoff valve. This valve should

be located in the same room, but external

to the range, and should be in a location that

allows ease of opening and closing. Do Not block

access to shutoff valve.

If rigid pipe is used as a gas supply

line, a combination of pipe fittings

must be used to obtain an in-line

connection to the range. All strains must be

removed from the supply and fuel lines so range

will be level and in line.

The regulator setting must be checked at

a minimum of 1 inch water column above

the manifold pressure. The inlet pressure

to the regulator should be as follows for operation:

Natural gas:

Manifold pressure — 5 inches

Maximum pressure — 14 inches

L.P. gas:

Manifold pressure — 10 inches

Maximum pressure — 14 inches

Line pressure testing:

Testing above 1/2 psi (gauge): The range

and its individual shutoff valve must be

disconnected from the gas supply piping system

during any pressure testing of that system at test

pressures greater than 1/2 psig (3.5 kPa).

Testing at 1/2 psi (gauge) or lower: The range must

be isolated from the gas supply piping system by

closing its individual manual shutoff valve during

any pressure testing of the gas supply piping

system at test pressures equal to or less than

1/2 psig (3.5 kPa).

Electrical

requirements

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result

to range

in death, fire, or electrical shock.

If codes permit and a separate ground wire is

used, it is recommended that a qualified electrician

determine that the ground path is adequate.

Check with a qualified electrician if you are not

sure whether the range is properly grounded.

Do not ground to a gas pipe.

A 120-volt, 60-Hz, AC-only, 15-ampere, fused

electrical circuit is required. A time-delay fuse or

circuit breaker is recommended. It is recommended

that a separate circuit serving only this range be

provided.

Electronic ignition systems operate within wide

voltage limits, but proper ground and polarity are

necessary. In addition to checking that the outlet

provides 120-volt power and is correctly grounded,

the outlet must be checked by a qualified

electrician to see if it is wired with correct polarity.

The wiring diagram is included in the literature

package. The wiring diagram can also be found on

the back of the range.

NOTE: The metal chassis of the range must be

grounded in order for the control panel to work. If

the metal chassis of the range is not grounded, no

keypads will operate. Check with a qualified

electrician if you are in doubt as to whether the

metal chassis of range is grounded.

Recommended ground method

For personal safety, this range is equipped with a

power supply cord having a 3-prong ground plug.

To minimize possible shock hazard, the cord must

be plugged into a mating 3-prong, ground-type

outlet, grounded in accordance with the National

Electrical Code, ANSI/NFPA 70 — latest edition*

or CSA Standard C22.1, Canadian Electrical Code,

Part 1, — latest edition** and all local codes and

ordinances. If a mating outlet is not available, it is

the personal responsibility and obligation of the

customer to have a properly grounded, 3-prong

outlet installed by a qualified electrician.

WARNING - Improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or

servicemen if you are in doubt as to whether the

appliance is properly grounded. Do not modify the

plug provided with the appliance - if it will not fit the

outlet, have a proper outlet installed by a qualified

electrician.

power

supply

cord

3-prong

ground plug

WARNING

3-prong

ground-type outlet

ground

prong