Jandy Jandy Pro Series Инструкции по установке

Печатать страницу

Jandy Jandy Pro Series Инструкции по установке

4. INSTALL BLOWER

Installation must be done in accordance with the National Electrical Code® ("NEC®"

or NFPA-70®) in the US, the Canadian Electrical Code ("CEC" or CSA C22.1) in

Canada, and/or any other local and national installation codes.

1. Refer to the "Select Blower" section (facing page) to ensure that you

have the correct blower size for your application.

2. Pressure tests to the system should be done prior to the installation

of the blower. See Warning Section on adjacent page.

3. Use 2" PVC pipe from the blower to jets or bubblers.

4. Slide Blower onto PVC Pipe. Lower until the stop

tabs make contact with the PVC pipe.

5. Blower should be installed vertically, away from

direct sunlight.

6. Do not glue or otherwise permanently attach the

blower to plumbing.

7. Do not remove the blower check valve diaphragm.

8. Drill two (2) 1/8" pilot holes through the textured fastener safe area

marked on the blower body. The holes should be drilled through the blower

body and PVC pipe. The holes should be oriented 180°

from one another.

9. Install one (1) 1/2" 8-18 thread forming screw into

each of the previously drilled pilot holes. The screws and

Do not use chemical adhesives to

afﬁ x the blower to the air inlet line.

pipe should not interfere with the normal travel of the

Fumes from chemical adhesives

check valve diaphragm.

may accumulate in the piping and

10. The blower also comes equipped with a mounting

explode causing property damage,

bracket which can be used to secure the blower to a

serious injury or death.

vertical surface

such as a wall or

post.

Flat

11. If not used

the bracket can

be removed and

stored.

Fastener

Flexed

Safe Area

1/8" Bit

for Pilot Holes

PVC

180°

Blower Body

CAUTION

Blower must be afﬁ xed to the plumbing using the fasteners

recommended in these instructions. Failure to do so may

allow the blower to come free of the plumbing during oper-

ation which could damage equipment and prevent proper

blower operation.

WARNING

Blower must be installed in an area well away from sourc-

es of exhaust such as gas pool and spa heater. Please

ensure that this blower is installed according to local codes

and Authority Having Jurisdiction (AHJ) requirements.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

WARNING

who is licensed and qualiﬁ ed in pool equipment by the jurisdiction in which the product will be installed where

such state or local requirements exist, the maintainer must be a professional with sufﬁ cient experience in

pool equipment installation and maintenance so that all of the instructions in this manual can be followed

exactly. Before installing this product, read and follow all warning notices and instructions that accompany

this product. Failure to follow warning notices and instructions may result in property damage, personal

injury, or death. Improper installation and/or operation will void the warranty. Improper installation and/or

operation can create unwanted electrical hazard which can cause serious injury, property damage, or death.

Turn off all circuit breakers required in order to prevent the possibility of electric shock. If you have any

Blower

questions or need further details please contact Zodiac Pool Systems Customer Support at: 1.800.822.7933

WARNING

using nonmetallic plumbing. Install blower no less than 1 foot (305 mm) above the maximum water level

or with an approved Hartford loop conﬁ guration as outlined in section 2 "Plumbing" to prevent water from

contacting electrical equipment. Install in accordance with the installation instructions.

To minimize the risk of severe injury or death the

appliance should not be subjected to the piping

system pressurization test. Local codes may

2" PVC

require the pool piping system to be subjected to a

pressure test. These requirements are generally not

intended to apply to the pool equipment. Zodiac

pool equipment is pressure tested at the factory.

However, if the WARNING cannot be followed and

pressure testing of the piping system must include

the appliance, BE SURE TO COMPLY WITH THE

FOLLOWING SAFETY INSTRUCTIONS:

WARNING

- Check all clamps, bolts, lids, lock rings and

system accessories to ensure they are properly

installed and secured before testing.

- RELEASE ALL AIR in the system before testing

- Test water pressure must NOT EXCEED 35 PSI.

- Water temperature for test must NOT EXCEED

100°F (38°C).

Limit test to 24 hours. After test, visually check

system to be sure it is ready for operation.

NOTICE: these parameters apply to Zodiac

equipment only. For non-Zodiac equipment, consult

equipment manufacturer.

Installation must be done in accordance with the

National Electrical Code

in the US, the Canadian Electrical Code ("CEC" or

Diaphragm

C22.1) in Canada, and/or any other local and national

installation codes.

Stop Tabs

RISK OF ELECTRIC SHOCK, FIRE, PERSONAL

INJURY, OR DEATH. When required by applicable

Fastener

local codes and/or by the Authority having jurisdiction

Safe Area

(AHJ); Connect only to a branch circuit that is

protected by a ground-fault circuit interrupter (GFCI).

Contact a qualified electrician if you cannot verify that

Diaphragm

the circuit is protected by a GFCI. Make sure such a

Travel

Distance

GFCI is provided by the installer and should be tested

on a routine basis. To test the GFCI, push the test

button. The GFCI should interrupt power. Push the

reset button. Power should be restored. If the GFCI

fails to operate in this manner, the GFCI is defective.

Fastener

If the GFCI interrupts power to the blower without the

Safe Area

test button being pushed, a ground current is flowing,

indicating the possibility of electrical shock. Do

not use the device. Disconnect the device and

have the problem corrected by a qualified service

representative before using.

- To reduce the risk of injury, do not permit

children to use this product.

- Jandy Blowers are powered by high-voltage

electric motors and must be installed by a licensed

or - certiﬁ ed electrician or a qualiﬁ ed swimming pool

service technician.

- Incorrectly installed equipment may fail, causing

severe injury or property damage.

- Do not install on a plumbing line that can be

closed or shut off. The blower may create severe

enough pressures to cause property damage or

injury.

Moutning Bracket

H0507900_REVJ

: FOR YOUR SAFETY - This product must be installed and serviced by a contractor

: RISK OF ELECTRIC SHOCK - Install at least 5 feet (1.5 m) from tub water

To Reduce the Risk of Injury -

a) The water in a spa should never exceed 104°F

(40°C). Water temperatures between 100°F (38°C)

and 104°F (40°C) are considered safe for a healthy

adult. Lower water temperatures are recommended

for young children and when spa use exceeds 10

minutes.

b) Since excessive water temperatures have a high

potential for causing fetal damage during the early

months of pregnancy, pregnant or possibly preg-

nant women should limit spa water temperatures to

100°F (38°C).

c) Before entering a spa or hot tub, the user should

measure the water temperature with an accurate

thermometer since the tolerance of water tempera-

ture-regulating devices varies.

d) The use of alcohol, drugs, or medication before

or during spa or hot tub use may lead to uncon-

sciousness with the possibility of drowning and can

greatly increase the risk of fatal hyperthermia.

e) Obese persons and persons with a history of

heart disease, low or high blood pressure, circula-

tory system problems, or diabetes should consult a

("NEC

" or NFPA-70

)

physician before using a spa.

f) Persons using medication should consult a

physician before using a spa or hot tub since some

medication may induce drowsiness while other

medication may affect heart rate, blood pressure,

and circulation.

g) People with infectious diseases should not use a

spa or hot tub.

h) Exercise care when entering or exiting the spa

or hot tub.

i) Water temperature in excess of 100°F (38°C)

may be injurious to your health.

j) Do not use a spa or hot tub immediately following

strenuous exercise.

k) Prolonged immersion in a spa or hot tub may be

injurious to your health.

l) Do not permit any electric appli-

ance (such as a light, telephone,

radio, or television) within ﬁ ve 5 feet

(1.5m) of a spa or hot tub.

Attention installer: This manual contains important

information about the installation, operation and safe use

of this product. This information should be given to the

owner/operator of this equipment.

SAVE THESE INSTRUCTIONS

Installation Instructions

Pool and Spa

Air Blower

Models:

PSB110

PSB115

PSB210

PSB215

PSB120

PSB220