Jandy Versa-Plumb CL580 Руководство по установке и эксплуатации - Страница 6

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Фильтр для плавательного бассейна Jandy Versa-Plumb CL580. Jandy Versa-Plumb CL580 20 страниц. Cartridge pool filters
Также для Jandy Versa-Plumb CL580: Руководство по установке и эксплуатации (14 страниц), Руководство по установке и эксплуатации (20 страниц), Руководство по установке и эксплуатации (20 страниц)

Печатать страницу

Jandy Versa-Plumb CL580 Руководство по установке и эксплуатации

Page 6

Section 3. Installation Instructions

WARNING

Use equipment only in a pool or spa installation.

Do not connect system to an unregulated city water

system or other external source of pressurized

water producing pressures greater than 35 psi.

3.1 Filter Location

Select a well-drained area, one that does not ﬂ ood

when it rains. Damp, non-ventilated areas should

be avoided.

Provide solid mounting for the ﬁ lter and pump

system. Install system on a concrete slab or solid

concrete blocks to avoid risk of settlement. Do not

use sand to level the ﬁ lter as the sand will wash

away. Filter systems can weigh up to 800 lbs.

Install electrical controls at least ﬁ ve (5) feet from

the ﬁ lter. This will allow enough room to stand

away from the ﬁ lter during start-up.

Allow sufﬁ cient clearance around the ﬁ lter to

permit a visual inspection of the clamp ring

(see Fig. 2).

Allow sufﬁ cient space above the ﬁ lter to remove

the ﬁ lter lid and ﬁ lter element for cleaning and

servicing.

Position the ﬁ lter to safely direct water drainage.

Align the air release valve to safely direct purged

air or water.

WARNING

Water discharged from an improperly positioned

filter or valve can create an electrical hazard

which can cause death, serious injury or property

damage.

CAUTION

Maintain your pressure gauge in good work ing

order. The pressure gauge is the primary indicator

of how the filter is operating.

6" MINIMUM CLEARANCE

FILTER

Figure 2.

Filter Location

Cartridge Pool Filters - CL and CV Series Filters

6" MINIMUM

CLEARANCE

If the ﬁ lter needs to be located above the water

level of the pool, it can be raised 2.5 ft. without

affecting the pump efﬁ ciency. A check valve is

recommended on the suction line to the pump.

If the ﬁ lter is to be installed below the water level

of the pool, isolation valves should be installed on

both the suction and return lines to prevent back

ﬂ ow of pool water during any routine servicing

that may be required.

3.2 Anchor Bracket Installation

In some areas, for example Florida, building codes

require that all appliances be securely fastened to the

equipment pad in order to withstand high wind pressures

created by hurricanes. Zodiac Pool Systems, Inc.

provides an anchor bracket kit for this purpose. Please

see the Parts List in Section 9 of this manual for the

correct part number. Follow the Anchor Bracket Installa-

tion Kit Instructions to attach the brackets to the ﬁ lter.

NOTE Anchor screws and washers for securing the

anchor bracket to the equipment pad are not

included with the ﬁ lter or the anchor bracket

kit. Zodiac recommends that a ¼" x 2¼" long

stainless steel Tapcon

stainless steel ﬂ at washer are used to mount

each anchor bracket to the equipment pad. The

Tapcon concrete screw meets Florida building

code requirements.

After placing the ﬁ lter on the equipment pad, as outlined

in Section 3.1, drill a 5/32" hole in the concrete at each

of the four (4) brackets on the ﬁ lter. (The correct size

concrete drill bit should be obtained when the concrete

screws are purchased.)

Install the Tapcon screws and washers through each of

the four (4) anchor brackets to secure the ﬁ lter to the

equipment pad. See Figure 3. Do not over-torque the

screws.

3.3 Filter Preparation

Check carton for damage due to rough handling

in shipment. If carton or any ﬁ lter components are

damaged, notify carrier immediately.

Carefully remove the accessory package.

A visual inspection of all parts should be made

now. See parts list in Section 9.

With the carton in an upright position, remove the

ﬁ lter tank from the carton.

To mount the pressure gauge/air release assembly

to the top of the ﬁ lter tank (located in the accessory

bag):

Place the smaller, thicker o-ring onto the

threads of the tank adapter (see Figure 4).

Slide the tank adapter through the coupling

concrete screw and