Jandy Infinite WaterColors IWCP50W100 Руководство по установке и эксплуатации - Страница 5

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Контроллер Jandy Infinite WaterColors IWCP50W100. Jandy Infinite WaterColors IWCP50W100 12 страниц. Led lighting
Также для Jandy Infinite WaterColors IWCP50W100: Руководство по установке и эксплуатации (12 страниц), Руководство (2 страниц)

Печатать страницу

Jandy

Infinite WaterColors

The junction box or Infinite WaterColors LED

Light Controller suitable for direct conduit

connection to lights must be located at least (8)

inches above water level, at least four (4) inches

above ground level, and at least (48) inches (4)

feet from the edge of the pool, or as required by

local code, See Figure 1.

The light fixture and all metal items within five

(5) feet of the pool must be properly electrically

bonded to a reliable point of grounding.

The wet niche must be properly installed so that

the top edge of the underwater light's lens is at

least (18) inches below the surface of the water in

the pool. See Figure 1.

The wet niche must be properly electrically

bonded and grounded via the No. 8 AWG ground

connector located at the rear of the niche.

See Figure 1.

National Electrical Code® (NEC®) requires bonding

of the Pool Water. Where none of the bonded pool

equipment, structures, or parts are in direct connection

with the pool water; the pool water shall be in direct

contact with an approved corrosion-resistant conductive

surface that exposes not less than 5800 mm² (9 in²) of the

surface area to the pool water at all times. The conductive

surface shall be located where it is not exposed to

physical damage or dislodgement during usual pool

activities, and it shall be bonded in accordance with the

bonding requirements of NEC Article 680. Refer to

locally enforced codes for any additional pool and spa

bonding requirements.

NOTE

To be certain that the pool's electrical system meets

all applicable requirements, the electrician should also

consult the local building department.

Use only approved wet niches (see following note) to

ensure a safe and proper installation.

NOTE

Jandy lights are ETL listed (ETL report/file

3141154CHI) for installation with only the following

manufacturer's wet niche fixtures:

Large Niche Model Numbers:

Jandy: PLNICLRG, PLNICVFLRG,

WT000002, SSNICLRG1R, SSNICLRG1S

Pentair: 620004, 78210200 thru 700, 78210401

Hayward DuraNiche: SP0600U

Small Niche Model Numbers:

Jandy: PLNICSM, SSNICSM,

Pentair: 79206600

Pentair

and Sta-Rite

are registered trademarks of Pentair, Inc.

® ®

Hayward

is a registered trademark and DuraNiche

® ®

of Hayward Pool Products, Inc.

Pool & Spa LED Lights

Installation and Operation Manual

™

is a trademark

™ ™

To GFCI, Circuit

Breaker and

Power Source.

48"

min.

Check AHJ and local code for additional requirements.

4" min.

Rigid

Conduit

#8 AWG Ground

Connector bonding

is located at rear

of niche.

Figure 1.

Jandy Infinite WaterColors Light

Installation

3.2

Installing the Light Fixture

NOTE

Perform these steps only after the electrical system

requirements are met.

Feed cord through conduit to junction box,

leaving at least four (4) feet of cord at the light

fixture to coil into the base of the light niche, see

Figure 1. The four (4) feet of cord allows the light

to be serviced after the pool is filled with water.

Cut the cord at the junction box, leaving at least

six (6) inches of cord to make connections.

Strip six (6) inches of the outer cord jacket to

expose the three insulated wires. Be careful not to

damage the insulation on the three (3) inner wires.

Install strain relief over cord jacket and connect

the light wires to the controller, black to orange,

white to orange, and green to the ground terminal

bar. Install the junction box cover.

Coil the 4-foot length of cord around the fixture

or into the base of the pool niche, and place the

light assembly into the niche.

Engage the retainer tab on the bottom of the face

ring, then pivot the top of the fixture inward and

tighten the special pilot screw.

WARNING

Use only the special pilot screw provided with this

underwater light. This screw mounts and electrically

grounds the housing securely to the mounting ring

and wet niche. Failure to use the screw provided could

create an electrical hazard, which could result in death

or serious injury to pool or spa users, installers or

others due to electrical shock.

ENGLISH

8" min. Junction Box or Infinite

WaterColors LED Light Controller,

to the max water level of the pool.

18" min. to top of Lens.

Concrete must be cut

back around Niche to

allow for a compacted

plaster seal.

11.50"

Coil 4 ft. of light cable

around Fixture.

16"

Page 5