Page 10
English
6.2
To Reset to the Beginning of the Color
sequence
Turn the light OFF, wait four (4) to five (5) seconds, then
turn ON, the light will return to the beginning of the color
cycle (Alpine White).
nOTE
If an AquaLink RS control system is being used the
color set can be selected using the indoor controller.
nOTE
To synchronize colors on multiple Jandy Pro Series
WaterColors Light systems wired to separate switches,
perform the above actions on all of their switches
simultaneously. All Jandy Pro Series WaterColors
Lights will synchronize automatically if activated by the
same switch. No other accessories are required.
section 7. Replacing light
Engine (PCB)
WARning
Always disconnect power to the color light at the
circuit breaker before servicing the light. Failure to do
so could result in death or serious injury to installer,
serviceman, pool or spa users or others due to
electrical shock.
1.
Turn off the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2.
Be sure to have the following items:
• A new lens gasket, P/N R0451101 for the large
light or P/N R0400501 for the small light.
• A light engine. See Table 2 for specification.
WARning
Replace light engine with the same type. Failure
to replace the light engine with the same type will
damage the light assembly and may cause an
electrical hazard resulting in death or serious injury to
pool or spa users, installers, or others due to electrical
shock, and may also cause damage to property. Be
sure the power is switched OFF before removing or
installing PCB. Allow PCB to cool before replacing.
3.
To remove the light assembly, unscrew the special
pilot screw at the top of the face ring, remove
light assembly from niche and gently place
assembly on the deck. It is not necessary to drain
down the pool. See Figure 6.
Jandy
Pro Series, WaterColors LED Lights
®
Table 2.
Jandy Pro series
Model
WaterColors
large light
WaterColors
large light
WaterColors
small light
WaterColors
small light
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided could
create an electrical hazard, which could result in death
or serious injury to pool or spa users, installers or
others due to electrical shock.
4.
a. Loosen the Phillips head screws (six (6) for
b. Remove the bottom clamp, the face ring
5.
a. 12V Small Light Engine (PCB) Replacement
|
Installation Manual
light specifications
Fixture
Voltage
12 Volt AC
120 Volt AC
12 Volt AC
120 Volt AC
WARning
Pool Clamp Removal.
small light, eight (8) for large light) to allow
the bottom clamp to be removed from the face
ring assembly. Do not remove the screws or the
retaining rings. The retaining rings prevent the
screws from falling free from the bottom clamp
and also aid in ease of assembly.
assembly, the glass lens, and the gasket from the
fixture. Remove the gasket from the lens. Refer
to Section 9, Exploded View and Replacement
Parts.
Light Engine Replacement
1. Remove two (2) nuts and two (2) washers.
2. Unplug the quick disconnect terminals from
the light engine.
3. Remove the light engine from the light
fixture.
4. Place new light engine into the fixture with
the orientation shown in Figure 7.
5
Secure the light engine with one (1) nylon
washer and one (1) nut. Torque to 12 in-lbs.
6. Place a nylon washer on the other stud and
place the green ground wire terminal on the
nylon washer and secure both with the nut.
Torque to 12 in-lbs.
light Engine (PCB)
Part number
R0474000
R0474100
R0473900
R0473900
Печатать страницу